LED lighting-equivalent and energy-savings calculator

The LED lumens and watts that match your bulbs or fixtures, and the kWh, dollars and CO₂ you save each year

In short

A lumen equivalent is the LED that matches an older bulb or fixture by its light output in lumens. A 60 W incandescent bulb gives about 800 lumens, which an LED matches with roughly 8–9 W; LED watts equal the target lumens divided by LED efficacy. Commercial fixtures are matched by delivered lumens and system watts, not lamp watts.

Choose the bulb or fixture you are replacing, and this calculator converts it into equivalent LED lumens and watts, then estimates the kilowatt-hours, money and CO₂ you save each year. For metal-halide, high-pressure sodium and fluorescent fixtures it adds the net cost after rebates, simple payback and 5-year return. Everything runs in your browser, and you can copy the results, share a link with your values and print a spec sheet.

Energy savings calculator

This calculator converts the incandescent, halogen or CFL bulbs you use into equivalent LED lumens and watts, then estimates the kilowatt-hours, money and CO₂ you save each year. For example, ten 60 W incandescent bulbs used five hours a day, replaced with 8 W LEDs, save about $160 a year at $0.17/kWh.

Lighting equivalent, savings and retrofit ROI

Choose the bulb or fixture you are replacing. Bulb lumens follow the U.S. FTC "Lighting Facts" values (60 W ≈ 800 lm); commercial fixtures use system watts and delivered lumens.

100 lm/W is a typical retrofit bulb; premium bulbs reach 120–150 lm/W. The U.S. average residential rate is roughly $0.16–0.18/kWh. Enter your own from your bill.

Annual savings
—
—Light output to match (per bulb)
—LED wattage needed (per bulb)
—Electricity saved per year
—Energy reduction
—Savings over a 25,000 h LED life
—Replacement bulbs avoided
—CO₂ avoided (at 0.37 kg/kWh, U.S. average)
Incandescent
—
LED
—

Free commercial retrofit & utility rebate estimate

Send your fixture details and we will email a free, no-obligation estimate of LED retrofit cost, energy savings and the utility rebates available where your facility is.

We use these details only to prepare your estimate and contact you about it. See the privacy notice.

Lumen equivalents

Match brightness by lumens: a 40 W incandescent gives about 450 lumens, 60 W about 800, 75 W about 1,100, 100 W about 1,600 and 150 W about 2,600. At roughly 100 lumens per watt, LEDs match them with about 4–5, 8–9, 11–12, 14–16 and 22–26 watts.

Approximate light output of common bulbs and the LED wattage that matches them.
IncandescentHalogenCFLLight outputLED (≈100 lm/W)
25 W18 W5 W~210–250 lm2–3 W
40 W29 W9 W~450 lm4–5 W
60 W43 W13 W~800 lm8–9 W
75 W53 W18 W~1,100 lm11–12 W
100 W72 W23 W~1,600 lm14–16 W
150 W—42 W~2,600 lm22–26 W

Method and assumptions

Annual energy equals watts × bulbs × hours per day × 365 ÷ 1,000, and LED watts equal the target lumens divided by LED efficacy. Lifetime savings assume a 25,000-hour LED versus about 1,000 hours for incandescent, 2,000 for halogen and 8,000 for CFL, and CO₂ uses a U.S. grid average of 0.37 kg/kWh.

Annual energy = watts × number of bulbs × hours per day × 365 ÷ 1,000. LED watts = target lumens ÷ LED efficacy. The lifetime figure assumes a 25,000-hour LED, compared with roughly 1,000 h for incandescent, 2,000 h for halogen and 8,000 h for CFL bulbs, which gives the count of replacement bulbs avoided. CO₂ uses an approximate U.S. grid average of 0.37 kg per kWh, and your utility's figure may be higher or lower. Real-world savings also depend on dimming, controls and fixture losses.

For commercial fixtures the calculator switches to a 50,000-hour LED fixture life and to lamp lives of about 15,000 h for metal halide, 24,000 h for high-pressure sodium, 20,000 h for T12, 30,000 h for T8 and 25,000 h for T5HO lamps. It also uses system watts, which include ballast losses, and delivered lumens, explained in the next section.

Commercial fixture equivalents: metal halide, HPS and fluorescent

Match commercial fixtures by delivered lumens and system watts, not lamp watts. A 400 W metal-halide high-bay draws about 458 W with its ballast and delivers roughly 19,000 lumens, which a 135–150 W LED high-bay matches. A three-lamp T8 troffer drawing 85 W is matched by a 35–40 W LED panel.

A lamp's rated lumens overstate what reaches the floor. Metal-halide lamps lose 20–35% of their output by mid-life, and the reflector, lens and lamp position in a high-bay or troffer absorb another 15–35%, while an LED fixture's lumens are measured leaving the fixture. The calculator therefore compares delivered lumens: rated lamp lumens × mean lumen maintenance × fixture efficiency. Ballasts add their own losses on top of the lamp watts, which is why a "400 W" metal-halide fixture draws about 458 W from the panel.

System watts include the ballast. Delivered lumens are mean lamp lumens after fixture losses. LED watts assume 140 lm/W, typical of current DLC-listed high-bays, area lights and troffers.
Existing fixtureSystem wattsDelivered lumensLED at 140 lm/WEnergy saved
Metal halide, 175 W lamp210 W~7,350 lm~53 W75%
Metal halide, 250 W lamp295 W~10,760 lm~77 W74%
Metal halide, 400 W lamp (high-bay)458 W~18,900 lm~135 W71%
Metal halide, 1000 W lamp (sports, flood)1,080 W~57,750 lm~413 W62%
High-pressure sodium, 150 W lamp188 W~8,640 lm~62 W67%
High-pressure sodium, 250 W lamp295 W~15,120 lm~108 W63%
High-pressure sodium, 400 W lamp465 W~27,000 lm~193 W59%
High-pressure sodium, 1000 W lamp1,100 W~75,600 lm~540 W51%
T12, 2 × 40 W, magnetic ballast86 W~2,930 lm~21 W76%
T8, 2 × 32 W59 W~3,410 lm~24 W59%
T8, 3 × 32 W troffer85 W~5,120 lm~37 W57%
T8, 4 × 32 W112 W~6,820 lm~49 W57%
T5HO, 4 × 54 W high-bay234 W~15,810 lm~113 W52%
T5HO, 6 × 54 W high-bay351 W~23,700 lm~169 W52%

These are conservative lumen-for-lumen matches. In practice, LED area and street lights often replace high-pressure sodium with fewer lumens, because their optics put light where it is needed and their whiter light gives better visibility at night, so a 150–180 W LED commonly replaces a 400 W HPS cobra-head. In warehouses, fluorescent and T5HO high-bays are often already efficient, so most of the gain there comes from occupancy sensors and longer life rather than watts alone.

Payback, ROI and utility rebates

Simple payback is the net project cost after utility rebates divided by the annual energy savings. Retrofits that replace metal halide or high-pressure sodium fixtures running 12 hours a day often pay back within one to three years, and avoided relamping, lift rental and occupancy sensors shorten that further.

When you pick a commercial fixture, the calculator shows an ROI breakdown. It multiplies the installed cost of each LED fixture, minus the utility rebate, by the fixture count to get the net project cost, then divides that by the annual energy savings for a simple payback. The 5-year net return is five years of energy savings minus the net cost. Use your blended electricity rate, the total bill divided by the kWh used, so demand charges are included; the U.S. average commercial price is about 13 cents per kWh.

Utility rebates are usually paid per fixture or per watt removed, and they generally require products listed by the DesignLights Consortium (DLC) or ENERGY STAR. Prescriptive rebates typically run from about $10–40 for a troffer retrofit kit to $50–150 for a high-bay or area light, and many utilities also offer custom incentives based on measured kWh savings. Check the program before buying, because many require pre-approval; the DSIRE database lists incentives by state.

Energy is only part of the return. Metal-halide fixtures are often group-relamped every two to three years with a lift truck, and LED fixtures rated for 50,000 hours or more to L70 (see LED lifespan) remove most of that cost. Occupancy and daylight sensors, which LEDs tolerate because they switch on instantly, typically cut a further 20–40% in warehouses and offices. LEDs also put less heat into the space, which lowers cooling loads in air-conditioned buildings. If you are planning a project, the estimate button under the ROI breakdown sends your fixture details for a free check of costs and rebates.

Frequently asked questions

How many lumens is a 60 W bulb?

About 800 lumens, which an LED matches with roughly 8–9 W.

How much money do LED bulbs save?

Replacing ten 60 W incandescent bulbs used 5 hours a day with 8 W LEDs saves about 950 kWh, or roughly $160 a year at $0.17/kWh.

What size LED replaces a 400 W metal halide?

A 400 W metal-halide high-bay draws about 458 W with its ballast and delivers roughly 19,000 lumens. An LED high-bay of about 135–150 W, at 125–140 lumens per watt, matches it while using about 70% less energy.

How long does a commercial LED retrofit take to pay back?

Often one to three years for fixtures that run long hours, such as warehouse high-bays and parking-lot lights. Payback is the net cost after rebates divided by the annual savings; the energy calculator above shows it for your fixture count, hours and electricity rate.

Sources and further reading

  1. U.S. Federal Trade Commission, Energy Labeling Rule (16 CFR Part 305) and the "Lighting Facts" label, with lumen equivalents for 40, 60, 75 and 100 W incandescent bulbs.
  2. U.S. Energy Information Administration (EIA), Electric Power Monthly, average retail price of electricity to residential and commercial customers.
  3. U.S. Environmental Protection Agency, Emissions & Generation Resource Integrated Database (eGRID), U.S. average CO₂ output emission rate.
  4. U.S. DOE, "LED Lighting" consumer guidance and Solid-State Lighting program reports on lamp efficacy.
  5. DesignLights Consortium (DLC), Solid-State Lighting Technical Requirements and Qualified Products List, efficacy requirements for commercial LED fixtures.
  6. NC Clean Energy Technology Center, DSIRE: Database of State Incentives for Renewables & Efficiency, utility lighting rebate programs.
  7. Lamp and ballast manufacturer catalogs: rated lumens, mean lumen maintenance and ballast input watts for metal-halide, high-pressure sodium, T12, T8 and T5HO systems.
Cite this page

IEEE

LEDlights.org. "LED lighting-equivalent and energy-savings calculator." LEDlights.org. https://ledlights.org/tools/led-energy-savings-calculator/ (accessed Nov. 16, 2026).

BibTeX

@misc{ledlights2026energycalculator,
  author       = {{LEDlights.org}},
  title        = {LED lighting-equivalent and energy-savings calculator},
  year         = {2026},
  month        = nov,
  howpublished = {\url{https://ledlights.org/tools/led-energy-savings-calculator/}},
  note         = {Accessed: 2026-11-16}
}

APA

LEDlights.org. (2026, November 16). LED lighting-equivalent and energy-savings calculator. https://ledlights.org/tools/led-energy-savings-calculator/

Markdown

[LED lighting-equivalent and energy-savings calculator](https://ledlights.org/tools/led-energy-savings-calculator/), LEDlights.org, updated November 16, 2026.

First published November 16, 2026 · Last updated November 16, 2026 · Found an error? Every figure on LEDlights.org is sourced; corrections are welcome.