LED frequently asked questions
Short answers to common questions about LEDs, from how they work to which bulb to buy
This page answers 27 common questions about LEDs in six groups: the basics, efficiency and lifespan, color quality, safety and health, dimming and electrical questions, and LED types and buying. Every answer is a few sentences long, and many link to the full article that covers the topic in depth.
LED basics
What is an LED?
An LED (light-emitting diode) is a semiconductor diode that emits light when current flows through it. Electrons and holes recombine at its p–n junction and release energy as photons, a process called electroluminescence. The color depends on the band gap; white LEDs add a phosphor to a blue chip.
Who invented the LED?
No single person. H. J. Round observed the effect in 1907 and Oleg Losev studied it in the 1920s. Biard and Pittman at Texas Instruments patented the first practical infrared LED (1961–62), and Nick Holonyak Jr. made the first visible red LED at GE in 1962. Akasaki, Amano and Nakamura won the 2014 Nobel Prize for the blue LED.
How do white LEDs work?
Most white LEDs use a blue InGaN chip at about 450 nm coated with a yellow YAG:Ce phosphor. The phosphor converts part of the blue into yellow, and the mixture looks white; adding red phosphor gives warmer light and higher CRI. Some premium LEDs use a violet chip with red, green and blue phosphors instead.
Efficiency and lifespan
Are LEDs more efficient than incandescent bulbs?
Yes, roughly 6–15 times. Incandescent bulbs give 10–17 lm/W and LEDs 80–230 lm/W, so an 8–9 W LED replaces a 60 W incandescent bulb and uses 75–90% less energy.
How long do LEDs last?
LED bulbs are typically rated 15,000–25,000 hours and LED fixtures 50,000–100,000 hours to L70, the point where output has fallen to 70%. Heat and driver quality matter most: a hot bulb in an enclosed fixture can fail within a few thousand hours. See LED lifespan.
What does L70 mean for LED lifespan?
L70 is the number of operating hours until an LED's light output falls to 70% of its initial value, roughly when people start to notice dimming. It is projected from IES LM-80 test data using the TM-21 method. An L70 of 50,000 hours equals about 11 years of 12-hour days.
Why do LED bulbs fail early?
Heat is the usual cause. Cheap bulbs overdrive their LEDs and use small heat sinks and low-temperature electrolytic capacitors, which dry out quickly, especially in enclosed or recessed fixtures. Power surges and incompatible dimmers also shorten life. Bulbs from reputable brands with longer warranties usually last far longer.
Can LED bulbs be used in enclosed fixtures?
Only if they are rated for enclosed fixtures. LEDs shed heat by conduction, and a sealed globe traps it, raising the LED and driver temperature and cutting lifespan sharply. Look for "enclosed fixture rated" on the package, or use a fixture with integrated LEDs designed for the enclosure.
Color quality
What color temperature should I choose?
Use 2700 K for living rooms and bedrooms, 3000 K for kitchens and bathrooms, 3500–4000 K for home offices, garages and workplaces, and 5000 K or more for workshops and color inspection. Keep one CCT per room, and consider dim-to-warm or tunable-white lamps for evenings. See the CCT guide.
What CRI is best for kitchen and bathroom lighting?
Safety and health
Do LEDs contain mercury?
No. Unlike CFLs and fluorescent tubes, LEDs contain no mercury. They do contain electronics and should be recycled as e-waste where possible.
Do LED lights get hot?
Much less than incandescent bulbs. An LED still turns a large share of its power into heat at the chip, so the base or heat sink feels warm, but the beam itself is cool. Household LED bulbs are not hot enough to start fires on wood or fabric in normal use; they can still soften plastics pressed against a hot driver or an overdriven chip in a sealed fixture. See thermal management.
Do LED lights emit UV?
White LED bulbs emit negligible UV. Specialty UV LEDs are sold for curing and disinfection and are a different product. UV-C can injure eyes and skin; use only enclosed, tested devices. Details: UV LEDs and How LEDs work FAQ.
Do LED lights cause cancer?
No. Normal white LED lighting has not been shown to cause cancer. Separate issues are evening sleep disruption from bright cool light and the skin/eye hazards of UV-C lamps. See blue light, sleep and eye safety.
Is the blue light from LEDs bad for your eyes?
Normal white LED lighting is safe: general-service LED lamps typically fall in the exempt or low-risk groups of the IEC 62471 photobiological safety standard, like other lamps of the same color temperature. Staring into any bright point source is unwise. Bright, cool light late in the evening can delay sleep, so use warm, dim light at night. The studies and standards are summarized in blue light, sleep and eye safety.
Are UV-C LEDs safe and effective for disinfection?
They are effective when the dose is right: 255–280 nm UV-C damages microbial DNA and RNA, and enclosed water and air units with tested log-reduction data work well. They are not safe for direct exposure, because UV-C injures eyes and skin within seconds to minutes at close range. Many cheap gadgets emit too little UV-C to disinfect. Full details: UV-C LED disinfection.
Do LED lights attract fewer bugs?
Generally, yes. Many night-flying insects are drawn most strongly to ultraviolet and blue light, which mercury-vapor and some fluorescent lamps emit and white LEDs emit little of. Warm-white (2700 K or lower) and amber LEDs attract the fewest insects, while cool-white LEDs still attract some.
Dimming and electrical
Why do some LED bulbs flicker?
Usually because of an incompatible dimmer, a low-quality driver with poor ripple filtering, or low-frequency PWM dimming. Use LED-rated trailing-edge dimmers, check the bulb maker's compatibility list and choose products specified as flicker-free. See LED drivers and flicker.
Can I use LED bulbs with a dimmer switch?
Yes, if the bulb is marked dimmable and the dimmer is LED-compatible. Old incandescent dimmers often need a minimum load of 40 W or more and cause flicker, buzzing or dropout with LEDs. Trailing-edge (ELV) dimmers usually work best; set the low-end trim and check the bulb maker's compatibility list.
Why do LED lights glow faintly when turned off?
A faint glow, or "ghosting", comes from tiny leakage currents: an illuminated or smart switch, a dimmer that passes a trickle current, voltage induced in long cable runs, or a switch wired in the neutral instead of the live conductor. LEDs need so little current that a few milliamps make them glow. An LED-compatible switch or a bleeder (load) device fixes it.
Why do LEDs need a driver instead of plugging straight into AC power?
An LED is a low-voltage DC device whose current rises exponentially with voltage. Mains power is 120 or 230 V AC and reverses polarity 100–120 times a second, so a driver must rectify it, step it down and regulate the current. Without one, the LED would conduct destructive current surges and fail almost instantly.
How do you calculate the right resistor for an LED?
Use R = (Vsupply − n × Vf) / If. For one 3.0 V white LED at 20 mA on a 5 V supply, R = (5 − 3.0) / 0.020 = 100 Ω. Round up to the next standard value and use a resistor rated at least twice its dissipation (I² × R). The resistor calculator does this automatically.
LED types and buying
What is the difference between SMD 2835 and SMD 5050?
A 2835 is a 2.8 × 3.5 mm single-chip LED on a large thermal pad, typically 0.2–1 W, and the most efficient choice for white light at 120–220 lm/W. A 5050 is 5 × 5 mm with three dies, ideal for RGB and addressable strips but less efficient for white. See the full comparison.
What is the difference between COB and SMD LEDs?
SMD LEDs are individual packages soldered across a board, spreading light over many points, and they are the most efficient option. COB LEDs bond many bare dies under one phosphor layer to form a single bright surface, ideal for spotlights with one crisp shadow and high CRI. CSP LEDs are smaller still, with no package at all. See COB vs SMD vs CSP.
What is the difference between Mini-LED, MicroLED and OLED?
Mini-LED is an LCD backlight made of thousands of tiny LEDs grouped into local-dimming zones. OLED makes every sub-pixel from organic emitters, giving perfect blacks with some burn-in risk. MicroLED makes every sub-pixel from a microscopic inorganic LED: perfect blacks, very high brightness and no burn-in, but still very expensive. See the display comparison.
What LED bulb replaces a 60 W incandescent?
An 800-lumen LED A19 bulb, usually 8–9 W. Match lumens rather than watts: about 450 lm replaces 40 W, 1,100 lm replaces 75 W and 1,600 lm replaces 100 W. Choose 2700 K to match the warm color of the old bulb.
What do IP65, IP67 and IP68 mean on LED lights?
They are IEC 60529 ingress-protection codes. The first digit 6 means dust-tight. The second digit rates water: 5 resists water jets, 7 survives immersion to 1 m for 30 minutes, and 8 survives continuous immersion beyond 1 m under conditions the maker specifies. IP65 suits outdoor fixtures, and IP67–IP68 suits in-ground and underwater lights.
Cite this page
IEEE
LEDlights.org. "LED frequently asked questions." LEDlights.org. https://ledlights.org/faq/ (accessed Nov. 16, 2026).BibTeX
@misc{ledlights2026faq,
author = {{LEDlights.org}},
title = {LED frequently asked questions},
year = {2026},
month = nov,
howpublished = {\url{https://ledlights.org/faq/}},
note = {Accessed: 2026-11-16}
}APA
LEDlights.org. (2026, November 16). LED frequently asked questions. https://ledlights.org/faq/
Markdown
[LED frequently asked questions](https://ledlights.org/faq/), LEDlights.org, updated November 16, 2026.