Glossary of LED terms

Short, precise definitions of the words used in LED datasheets, lighting standards and product listings

This glossary defines the terms used most often in LED datasheets, lighting standards and product listings, from band gap and electroluminescence to CRI, CCT, L70, binning, PPFD and IP ratings. Each entry gives a short, precise definition that matches how the term is used across this encyclopedia.

Semiconductor physics

These terms describe what happens inside the chip: the light-emitting diode itself, electroluminescence, the p–n junction, band gap, forward voltage, quantum wells and phosphors. They appear in LED datasheets and in the physics articles of this encyclopedia, and they explain why an LED emits one particular color at one particular voltage.

Light-emitting diode (LED)
A semiconductor diode that emits light when current flows forward through its p–n junction. The color is set by the band gap of the semiconductor, or by a phosphor in white LEDs. What is an LED?
Electroluminescence
Light emitted by a material in direct response to an electric current or field, rather than heat. In LEDs it comes from electrons and holes recombining at a junction. Recombination
p–n junction
The boundary between p-type (hole-rich) and n-type (electron-rich) semiconductor. Forward bias pushes both carriers into it, where they recombine and, in an LED, emit photons. The p–n junction
Band gap (Eg)
The energy between a semiconductor's valence and conduction bands, in electron-volts. It sets the photon energy and therefore the wavelength: λ (nm) ≈ 1240 / Eg (eV). Band gap and wavelength
Forward voltage (Vf)
The voltage across a conducting LED: about 1.2–1.5 V for infrared, 2 V for red, 3 V for blue and white, and 5–7 V for UV-C. Forward bias and current flow
Quantum well
A semiconductor layer only 2–3 nm thick that traps electrons and holes so they recombine efficiently. Modern LEDs stack several of them (multiple quantum wells) in the active region. Quantum wells
Phosphor (pc-LED)
A luminescent material, such as YAG:Ce, that absorbs blue or violet LED light and re-emits longer wavelengths. Phosphor-converted LEDs produce more than 95% of white LED light. Phosphor conversion

Light output and efficiency

These terms measure how much light an LED produces and how efficiently it does so: lumen, luminous efficacy, wall-plug efficiency, efficiency droop and the green gap. They are used on bulb packaging, in datasheets and in comparisons between LEDs and older light sources such as incandescent bulbs.

Lumen (lm)
The unit of luminous flux: the total visible light a source emits, weighted by the eye's sensitivity. A 60 W-equivalent bulb gives about 800 lm. Lumens, watts and efficacy
Luminous efficacy (lm/W)
Lumens produced per watt of electrical power. White LEDs reach 80–230 lm/W commercially, compared with 10–17 lm/W for incandescent bulbs. Efficacy compared
Wall-plug efficiency (WPE)
The share of electrical input power that leaves an LED as light. The best blue LEDs exceed 60%; UV-C LEDs reach only a few percent. How efficient is an LED?
Efficiency droop
The fall in LED efficiency at high current density, caused mainly by Auger recombination. It is why efficient designs run more LEDs at lower current. Recombination
Green gap
The dip in LED efficiency between about 530 and 590 nm, where neither InGaN nor AlInGaP performs well, and a main reason white LEDs use phosphors instead of RGB mixing. How efficient is an LED?

Color quality

These terms describe the color of white light and how faithfully it shows the colors of objects: correlated color temperature, Duv, the color rendering index, R9, TM-30, MacAdam ellipses and binning. They appear on lighting labels and in product specifications, and they decide whether lamps match each other.

Correlated color temperature (CCT)
How warm or cool white light looks, in kelvin, matched to a glowing black body: 2700 K is warm white, 4000 K neutral and 6500 K cool daylight. Color temperature
Duv
The distance of a light's color point above (greenish) or below (pinkish) the black-body curve. Good white LEDs stay within about ±0.006. Color consistency
Color rendering index (CRI, Ra)
A score up to 100 for how accurately a light renders eight pastel test colors compared with a reference source. Ra 80 is the commercial minimum; 90+ counts as high CRI. Color rendering index
R9
The CRI score for a saturated red test color, which is not part of Ra. Low R9 makes skin, wood and food look dull; look for R9 above 50. Why deep red matters
TM-30 (Rf, Rg)
The IES method that scores color fidelity (Rf) and gamut (Rg) with 99 color samples. It is more informative than CRI. Fidelity and gamut
MacAdam ellipse (SDCM)
A region of the color diagram used to measure color differences in steps. LEDs within a 1–2 step ellipse look identical; at 5 steps or more, differences can be visible. Color consistency
Binning
Sorting LEDs after manufacture into groups of similar flux, chromaticity and forward voltage, so that the LEDs in one product match in brightness and color. Why LEDs are binned

Heat and lifetime

These terms cover how heat affects an LED and how its working life is rated: junction temperature, thermal runaway, the metal-core circuit board (MCPCB), L70 lifetime and the LM-80 and TM-21 methods. They are used in thermal design, in lifetime claims on packaging and in manufacturers' test reports.

Junction temperature (Tj)
The temperature of the light-emitting region inside the chip. Higher Tj lowers light output, shifts color and shortens life. Thermal management
Thermal runaway
A loop in which current heats an LED, lowering its forward voltage, which draws more current and more heat until it fails. Resistors and constant-current drivers prevent it. Thermal runaway explained
MCPCB
A metal-core printed circuit board, usually aluminium, that spreads heat from high-power LEDs into a heat sink. The common 20 mm "star" board is an MCPCB. High-power LEDs
L70 lifetime
The operating hours until an LED's light output falls to 70% of its initial value. Quality LED luminaires are rated 50,000–100,000 h L70. Lumen maintenance
LM-80 and TM-21
IES LM-80 is the method for measuring LED lumen maintenance over at least 6,000 hours; IES TM-21 projects lifetime from that data, to at most six times the test duration. How LED packages are tested

Drivers and dimming

These terms describe how an LED is powered and dimmed: the LED driver, constant current and constant voltage, PWM dimming and flicker. They are used when choosing a power supply for strips, COBs and high-power LEDs, when matching bulbs to dimmer switches, and when judging whether a light is flicker-free.

LED driver
The power supply that converts mains or battery power into the regulated current or voltage an LED needs, often with dimming. Driver quality largely decides flicker and lifespan. Why LEDs need a driver
Constant current (CC) and constant voltage (CV)
CC drivers regulate current, for example 700 mA, for high-power LEDs and COBs. CV supplies deliver a fixed 12 or 24 V to strips that limit their own current. CC vs CV drivers
PWM dimming
Dimming by switching an LED fully on and off many times per second and varying the on-time (duty cycle). Low PWM frequencies can cause visible or on-camera flicker. How LEDs are dimmed
Flicker
Rapid, repetitive change in light output, often caused by poor drivers or low-frequency PWM. It is measured as percent flicker, Pst LM and SVM, and limited by IEEE 1789 guidance and EU ecodesign rules. What is LED flicker?

Packages, displays and applications

These terms name the physical forms LEDs are sold in and two ratings used when applying them: SMD, COB and CSP packages, addressable LEDs, OLED and MicroLED displays, PPFD for grow lights and IP ratings for dust and water protection. They appear in product listings for strips, bulbs, fixtures and screens.

SMD LED
A surface-mount LED soldered flat onto a circuit board. Its four-digit name is its size in tenths of a millimetre: a 2835 measures 2.8 × 3.5 mm. SMD LEDs
COB (chip-on-board)
Many bare LED dies bonded directly to one substrate under a single phosphor layer, forming one bright, uniform light-emitting surface for spotlights and downlights. COB and MCOB LEDs
CSP (chip-scale package)
A package barely larger than the die, usually a flip-chip with phosphor applied directly, soldered to the board without a lead frame or bond wires. CSP and flip-chip LEDs
Addressable LED
An RGB or RGBW LED with a built-in controller chip, such as the WS2812B, so every LED in a chain can show its own color, set over a data line. Addressable LEDs
OLED
An LED built from thin organic layers instead of a crystalline semiconductor, used as self-emissive pixels in phones, watches and TVs. Organic LEDs
MicroLED
A display in which every sub-pixel is a microscopic inorganic LED, typically under 50 µm, combining per-pixel contrast with high brightness and no burn-in. MicroLED displays
PPFD
Photosynthetic photon flux density: the number of 400–700 nm photons landing on a surface, in µmol/m²/s. It is the grow-light equivalent of lux. PAR, PPF and PPFD
IP rating
The IEC 60529 code for protection against dust and water. IP65 resists water jets, IP67 survives temporary immersion and IP68 continuous immersion. IP ratings table

Sources

  1. CIE S 017:2020, ILV: International Lighting Vocabulary, 2nd edition, International Commission on Illumination (CIE).
  2. IES LM-80-20, Measuring Luminous Flux and Color Maintenance of LED Packages, Arrays and Modules, and IES TM-21-21, Projecting Long-Term Luminous Flux Maintenance of LED Light Sources.
  3. ANSI C78.377-2017, Specifications for the Chromaticity of Solid-State Lighting Products.
  4. IEEE 1789-2015, Recommended Practices for Modulating Current in High-Brightness LEDs for Mitigating Health Risks to Viewers.
Cite this page

IEEE

LEDlights.org. "Glossary of LED terms." LEDlights.org. https://ledlights.org/glossary/ (accessed Nov. 16, 2026).

BibTeX

@misc{ledlights2026glossary,
  author       = {{LEDlights.org}},
  title        = {Glossary of LED terms},
  year         = {2026},
  month        = nov,
  howpublished = {\url{https://ledlights.org/glossary/}},
  note         = {Accessed: 2026-11-16}
}

APA

LEDlights.org. (2026, November 16). Glossary of LED terms. https://ledlights.org/glossary/

Markdown

[Glossary of LED terms](https://ledlights.org/glossary/), LEDlights.org, updated November 16, 2026.

First published November 16, 2026 · Last updated November 16, 2026 · Found an error? Every figure on LEDlights.org is sourced; corrections are welcome.