# LEDlights.org: the LED encyclopedia (full text for language models) > A compact Markdown edition of https://ledlights.org: every article's and guide's definition and section summaries, links to the guides' detailed sub-pages, the glossary and key specification tables. Text © 2026 LEDlights.org. Quote freely with attribution and a link to the source page. Units: lm = lumen, lm/W = luminous efficacy, K = kelvin (correlated color temperature), Ra = CRI general index, R9 = saturated-red rendering, µmol/m²/s = PPFD, nm = nanometre, Vf = forward voltage, Tj = junction temperature. ## Glossary Canonical page: https://ledlights.org/glossary/ (each term has its own anchor, such as https://ledlights.org/glossary/#term-led) - **Light-emitting diode (LED)**: A semiconductor diode that emits light when current flows forward through its p–n junction. The color is set by the band gap of the semiconductor, or by a phosphor in white LEDs. - **Electroluminescence**: Light emitted by a material in direct response to an electric current or field, rather than heat. In LEDs it comes from electrons and holes recombining at a junction. - **p–n junction**: The boundary between p-type (hole-rich) and n-type (electron-rich) semiconductor. Forward bias pushes both carriers into it, where they recombine and, in an LED, emit photons. - **Band gap (Eg)**: The energy between a semiconductor's valence and conduction bands, in electron-volts. It sets the photon energy and therefore the wavelength: λ (nm) ≈ 1240 / Eg (eV). - **Forward voltage (Vf)**: The voltage across a conducting LED: about 1.2–1.5 V for infrared, 2 V for red, 3 V for blue and white, and 5–7 V for UV-C. - **Quantum well**: A semiconductor layer only 2–3 nm thick that traps electrons and holes so they recombine efficiently. Modern LEDs stack several of them (multiple quantum wells) in the active region. - **Phosphor (pc-LED)**: A luminescent material, such as YAG:Ce, that absorbs blue or violet LED light and re-emits longer wavelengths. Phosphor-converted LEDs produce more than 95% of white LED light. - **Lumen (lm)**: The unit of luminous flux: the total visible light a source emits, weighted by the eye's sensitivity. A 60 W-equivalent bulb gives about 800 lm. - **Luminous efficacy (lm/W)**: Lumens produced per watt of electrical power. White LEDs reach 80–230 lm/W commercially, compared with 10–17 lm/W for incandescent bulbs. - **Wall-plug efficiency (WPE)**: The share of electrical input power that leaves an LED as light. The best blue LEDs exceed 60%; UV-C LEDs reach only a few percent. - **Efficiency droop**: The fall in LED efficiency at high current density, caused mainly by Auger recombination. It is why efficient designs run more LEDs at lower current. - **Green gap**: The dip in LED efficiency between about 530 and 590 nm, where neither InGaN nor AlInGaP performs well, and a main reason white LEDs use phosphors instead of RGB mixing. - **Correlated color temperature (CCT)**: How warm or cool white light looks, in kelvin, matched to a glowing black body: 2700 K is warm white, 4000 K neutral and 6500 K cool daylight. - **Duv**: The distance of a light's color point above (greenish) or below (pinkish) the black-body curve. Good white LEDs stay within about ±0.006. - **Color rendering index (CRI, Ra)**: A score up to 100 for how accurately a light renders eight pastel test colors compared with a reference source. Ra 80 is the commercial minimum; 90+ counts as high CRI. - **R9**: The CRI score for a saturated red test color, which is not part of Ra. Low R9 makes skin, wood and food look dull; look for R9 above 50. - **TM-30 (Rf, Rg)**: The IES method that scores color fidelity (Rf) and gamut (Rg) with 99 color samples. It is more informative than CRI. - **MacAdam ellipse (SDCM)**: A region of the color diagram used to measure color differences in steps. LEDs within a 1–2 step ellipse look identical; at 5 steps or more, differences can be visible. - **Binning**: Sorting LEDs after manufacture into groups of similar flux, chromaticity and forward voltage, so that the LEDs in one product match in brightness and color. - **Junction temperature (Tj)**: The temperature of the light-emitting region inside the chip. Higher Tj lowers light output, shifts color and shortens life. - **Thermal runaway**: A loop in which current heats an LED, lowering its forward voltage, which draws more current and more heat until it fails. Resistors and constant-current drivers prevent it. - **MCPCB**: A metal-core printed circuit board, usually aluminium, that spreads heat from high-power LEDs into a heat sink. The common 20 mm "star" board is an MCPCB. - **L70 lifetime**: The operating hours until an LED's light output falls to 70% of its initial value. Quality LED luminaires are rated 50,000–100,000 h L70. - **LM-80 and TM-21**: IES LM-80 is the method for measuring LED lumen maintenance over at least 6,000 hours; IES TM-21 projects lifetime from that data, to at most six times the test duration. - **LED driver**: The power supply that converts mains or battery power into the regulated current or voltage an LED needs, often with dimming. Driver quality largely decides flicker and lifespan. - **Constant current (CC) and constant voltage (CV)**: CC drivers regulate current, for example 700 mA, for high-power LEDs and COBs. CV supplies deliver a fixed 12 or 24 V to strips that limit their own current. - **PWM dimming**: Dimming by switching an LED fully on and off many times per second and varying the on-time (duty cycle). Low PWM frequencies can cause visible or on-camera flicker. - **Flicker**: Rapid, repetitive change in light output, often caused by poor drivers or low-frequency PWM. It is measured as percent flicker, Pst LM and SVM, and limited by IEEE 1789 guidance and EU ecodesign rules. - **SMD LED**: A surface-mount LED soldered flat onto a circuit board. Its four-digit name is its size in tenths of a millimetre: a 2835 measures 2.8 × 3.5 mm. - **COB (chip-on-board)**: Many bare LED dies bonded directly to one substrate under a single phosphor layer, forming one bright, uniform light-emitting surface for spotlights and downlights. - **CSP (chip-scale package)**: A package barely larger than the die, usually a flip-chip with phosphor applied directly, soldered to the board without a lead frame or bond wires. - **Addressable LED**: An RGB or RGBW LED with a built-in controller chip, such as the WS2812B, so every LED in a chain can show its own color, set over a data line. - **OLED**: An LED built from thin organic layers instead of a crystalline semiconductor, used as self-emissive pixels in phones, watches and TVs. - **MicroLED**: A display in which every sub-pixel is a microscopic inorganic LED, typically under 50 µm, combining per-pixel contrast with high brightness and no burn-in. - **PPFD**: Photosynthetic photon flux density: the number of 400–700 nm photons landing on a surface, in µmol/m²/s. It is the grow-light equivalent of lux. - **IP rating**: The IEC 60529 code for protection against dust and water. IP65 resists water jets, IP67 survives temporary immersion and IP68 continuous immersion. ## Frequently asked questions Canonical page: https://ledlights.org/faq/ **What is an LED?** An LED (light-emitting diode) is a semiconductor diode that emits light when current flows through it. Electrons and holes recombine at its p–n junction and release energy as photons, a process called electroluminescence. The color depends on the band gap; white LEDs add a phosphor to a blue chip. **Who invented the LED?** No single person. H. J. Round observed the effect in 1907 and Oleg Losev studied it in the 1920s. Biard and Pittman at Texas Instruments patented the first practical infrared LED (1961–62), and Nick Holonyak Jr. made the first visible red LED at GE in 1962. Akasaki, Amano and Nakamura won the 2014 Nobel Prize for the blue LED. **How do white LEDs work?** Most white LEDs use a blue InGaN chip at about 450 nm coated with a yellow YAG:Ce phosphor. The phosphor converts part of the blue into yellow, and the mixture looks white; adding red phosphor gives warmer light and higher CRI. Some premium LEDs use a violet chip with red, green and blue phosphors instead. **Are LEDs more efficient than incandescent bulbs?** Yes, roughly 6–15 times. Incandescent bulbs give 10–17 lm/W and LEDs 80–230 lm/W, so an 8–9 W LED replaces a 60 W incandescent bulb and uses 75–90% less energy. **How long do LEDs last?** LED bulbs are typically rated 15,000–25,000 hours and LED fixtures 50,000–100,000 hours to L70, the point where output has fallen to 70%. Heat and driver quality matter most: a hot bulb in an enclosed fixture can fail within a few thousand hours. See LED lifespan. **What does L70 mean for LED lifespan?** L70 is the number of operating hours until an LED's light output falls to 70% of its initial value, roughly when people start to notice dimming. It is projected from IES LM-80 test data using the TM-21 method. An L70 of 50,000 hours equals about 11 years of 12-hour days. **Why do LED bulbs fail early?** Heat is the usual cause. Cheap bulbs overdrive their LEDs and use small heat sinks and low-temperature electrolytic capacitors, which dry out quickly, especially in enclosed or recessed fixtures. Power surges and incompatible dimmers also shorten life. Bulbs from reputable brands with longer warranties usually last far longer. **Can LED bulbs be used in enclosed fixtures?** Only if they are rated for enclosed fixtures. LEDs shed heat by conduction, and a sealed globe traps it, raising the LED and driver temperature and cutting lifespan sharply. Look for "enclosed fixture rated" on the package, or use a fixture with integrated LEDs designed for the enclosure. **What color temperature should I choose?** Use 2700 K for living rooms and bedrooms, 3000 K for kitchens and bathrooms, 3500–4000 K for home offices, garages and workplaces, and 5000 K or more for workshops and color inspection. Keep one CCT per room, and consider dim-to-warm or tunable-white lamps for evenings. See the CCT guide. **What CRI is best for kitchen and bathroom lighting?** Choose CRI 90 or higher with an R9 value above 50, so food, skin and makeup look natural. 2700–3000 K suits most homes, and 3000–4000 K suits task lighting over worktops and mirrors. CRI 80 bulbs make reds look dull, which is most noticeable in kitchens and bathrooms. **Do LEDs contain mercury?** No. Unlike CFLs and fluorescent tubes, LEDs contain no mercury. They do contain electronics and should be recycled as e-waste where possible. **Do LED lights get hot?** Much less than incandescent bulbs. An LED still turns a large share of its power into heat at the chip, so the base or heat sink feels warm, but the beam itself is cool. Household LED bulbs are not hot enough to start fires on wood or fabric in normal use; they can still soften plastics pressed against a hot driver or an overdriven chip in a sealed fixture. See thermal management. **Do LED lights emit UV?** White LED bulbs emit negligible UV. Specialty UV LEDs are sold for curing and disinfection and are a different product. UV-C can injure eyes and skin; use only enclosed, tested devices. Details: UV LEDs and How LEDs work FAQ. **Do LED lights cause cancer?** No. Normal white LED lighting has not been shown to cause cancer. Separate issues are evening sleep disruption from bright cool light and the skin/eye hazards of UV-C lamps. See blue light, sleep and eye safety. **Is the blue light from LEDs bad for your eyes?** Normal white LED lighting is safe: general-service LED lamps typically fall in the exempt or low-risk groups of the IEC 62471 photobiological safety standard, like other lamps of the same color temperature. Staring into any bright point source is unwise. Bright, cool light late in the evening can delay sleep, so use warm, dim light at night. The studies and standards are summarized in blue light, sleep and eye safety. **Are UV-C LEDs safe and effective for disinfection?** They are effective when the dose is right: 255–280 nm UV-C damages microbial DNA and RNA, and enclosed water and air units with tested log-reduction data work well. They are not safe for direct exposure, because UV-C injures eyes and skin within seconds to minutes at close range. Many cheap gadgets emit too little UV-C to disinfect. Full details: UV-C LED disinfection. **Do LED lights attract fewer bugs?** Generally, yes. Many night-flying insects are drawn most strongly to ultraviolet and blue light, which mercury-vapor and some fluorescent lamps emit and white LEDs emit little of. Warm-white (2700 K or lower) and amber LEDs attract the fewest insects, while cool-white LEDs still attract some. **Why do some LED bulbs flicker?** Usually because of an incompatible dimmer, a low-quality driver with poor ripple filtering, or low-frequency PWM dimming. Use LED-rated trailing-edge dimmers, check the bulb maker's compatibility list and choose products specified as flicker-free. See LED drivers and flicker. **Can I use LED bulbs with a dimmer switch?** Yes, if the bulb is marked dimmable and the dimmer is LED-compatible. Old incandescent dimmers often need a minimum load of 40 W or more and cause flicker, buzzing or dropout with LEDs. Trailing-edge (ELV) dimmers usually work best; set the low-end trim and check the bulb maker's compatibility list. **Why do LED lights glow faintly when turned off?** A faint glow, or "ghosting", comes from tiny leakage currents: an illuminated or smart switch, a dimmer that passes a trickle current, voltage induced in long cable runs, or a switch wired in the neutral instead of the live conductor. LEDs need so little current that a few milliamps make them glow. An LED-compatible switch or a bleeder (load) device fixes it. **Why do LEDs need a driver instead of plugging straight into AC power?** An LED is a low-voltage DC device whose current rises exponentially with voltage. Mains power is 120 or 230 V AC and reverses polarity 100–120 times a second, so a driver must rectify it, step it down and regulate the current. Without one, the LED would conduct destructive current surges and fail almost instantly. **How do you calculate the right resistor for an LED?** Use R = (Vsupply − n × Vf) / If. For one 3.0 V white LED at 20 mA on a 5 V supply, R = (5 − 3.0) / 0.020 = 100 Ω. Round up to the next standard value and use a resistor rated at least twice its dissipation (I² × R). The resistor calculator does this automatically. **What is the difference between SMD 2835 and SMD 5050?** A 2835 is a 2.8 × 3.5 mm single-chip LED on a large thermal pad, typically 0.2–1 W, and the most efficient choice for white light at 120–220 lm/W. A 5050 is 5 × 5 mm with three dies, ideal for RGB and addressable strips but less efficient for white. See the full comparison. **What is the difference between COB and SMD LEDs?** SMD LEDs are individual packages soldered across a board, spreading light over many points, and they are the most efficient option. COB LEDs bond many bare dies under one phosphor layer to form a single bright surface, ideal for spotlights with one crisp shadow and high CRI. CSP LEDs are smaller still, with no package at all. See COB vs SMD vs CSP. **What is the difference between Mini-LED, MicroLED and OLED?** Mini-LED is an LCD backlight made of thousands of tiny LEDs grouped into local-dimming zones. OLED makes every sub-pixel from organic emitters, giving perfect blacks with some burn-in risk. MicroLED makes every sub-pixel from a microscopic inorganic LED: perfect blacks, very high brightness and no burn-in, but still very expensive. See the display comparison. **What LED bulb replaces a 60 W incandescent?** An 800-lumen LED A19 bulb, usually 8–9 W. Match lumens rather than watts: about 450 lm replaces 40 W, 1,100 lm replaces 75 W and 1,600 lm replaces 100 W. Choose 2700 K to match the warm color of the old bulb. **What do IP65, IP67 and IP68 mean on LED lights?** They are IEC 60529 ingress-protection codes. The first digit 6 means dust-tight. The second digit rates water: 5 resists water jets, 7 survives immersion to 1 m for 30 minutes, and 8 survives continuous immersion beyond 1 m under conditions the maker specifies. IP65 suits outdoor fixtures, and IP67–IP68 suits in-ground and underwater lights. --- # Light-emitting diode URL: https://ledlights.org/ · Updated: 2026-11-15 **Definition (Light-emitting diode):** A light-emitting diode (LED) is a semiconductor device that emits light when an electric current passes through it. Inside, electrons and holes recombine at a p–n junction and release energy as photons, a process called electroluminescence. The color is set by the semiconductor's band gap. White LEDs usually combine a blue chip with a yellow phosphor. ## What is an LED and how does it work? An LED is a semiconductor diode that turns electric current directly into light. Electrons from the n-type side and holes from the p-type side meet at the junction and recombine, releasing photons. The photon energy equals the band gap, so the material sets the color: λ (nm) ≈ 1240 / Eg (eV). ## A brief history LED history runs from H. J. Round's glowing carborundum in 1907 and Oleg Losev's studies in the 1920s to the first practical infrared and red LEDs in 1961–62. The efficient blue LED of 1993 enabled white LEDs in 1996 and won the 2014 Nobel Prize; LEDs now dominate lighting and displays. ## How LEDs make white light No semiconductor emits white light directly. More than 95% of white LEDs are phosphor-converted: a 450 nm blue chip excites a yellow YAG:Ce phosphor, and the blue-plus-yellow mix looks white. Red phosphor adds warmth and color rendering, RGB chips mix colors, and violet-pumped LEDs give full-spectrum light. ## Why LEDs replaced other light sources LEDs replaced incandescent, halogen, fluorescent and HID lamps because they are 5–15 times more efficient than incandescent, last 25,000–100,000 hours, contain no mercury, switch on instantly and dim smoothly. They are also directional, compact, robust and available at specific wavelengths for plants, medicine and sensing. Table: LEDs compared with incandescent, halogen, CFL, fluorescent and HID lamps |Light source|Efficacy (lm/W)|Life (h)|Instant on|Dimmable|Mercury| |---|---|---|---|---|---| |Incandescent|10–17|~1,000|Yes|Yes|No| |Halogen|15–24|2,000–4,000|Yes|Yes|No| |CFL|50–70|8,000–10,000|Slow warm-up|Limited|Yes| |Fluorescent tube|80–100|20,000–36,000|Mostly|With special ballast|Yes| |Metal halide / HPS|65–140|10,000–24,000|No (minutes)|Limited|Yes| |LED|80–220+|25,000–100,000|Yes|Yes, to <1%|No| ## The main LED families The main LED families are through-hole DIP indicators, surface-mount SMD packages such as 2835 and 5050, chip-on-board (COB) and chip-scale (CSP) modules, filament LEDs, high-power emitters, display technologies (OLED, QLED, Mini-LED and MicroLED), invisible infrared and ultraviolet LEDs, and addressable RGB pixels such as the WS2812B. --- # History of the LED URL: https://ledlights.org/history/ · Updated: 2026-11-14 **Definition:** The light-emitting diode took about 90 years to go from a lab curiosity to the world's main light source. Light from a semiconductor crystal was first seen in 1907. Practical infrared and red LEDs arrived in 1961–62. Yellow and brighter reds followed in the 1970s, the efficient blue LED in 1993 and the white LED in 1996. By the 2020s, LEDs made up more than half of global lighting sales. ## Interactive timeline The LED's history spans more than a century: H. J. Round saw light from carborundum in 1907, Holonyak made the first visible LED in 1962, the bright blue LED arrived in 1993 and the white LED in 1996, and LEDs passed half of global lighting sales in 2022. The timeline below covers each milestone. ## 1907: H. J. Round and the glowing carborundum In 1907 Henry Joseph Round, an engineer working for Marconi, reported in Electrical World that carborundum (silicon carbide) crystal detectors glowed yellow, green, orange or blue when a voltage was applied. It was the first published observation of electroluminescence from a solid, though Round never pursued it. ## 1920s: Oleg Losev, the forgotten pioneer Oleg Losev, a self-taught Soviet radio physicist, published about sixteen papers between 1924 and 1930 proving that the glow from carborundum detectors was not heat and came from a thin active layer. In 1927 he applied for a patent on a "light relay" for optical signalling. He died in the Siege of Leningrad in 1942. ## 1930s–1950s: Naming and explaining the glow In 1936 Georges Destriau made zinc sulfide powders glow in an alternating field and coined the word electroluminescence. The explanation came with transistor-era semiconductor theory: in 1951 Kurt Lehovec and colleagues showed the light comes from carriers injected across a p–n junction that recombine and emit photons. ## 1955–1962: Infrared LEDs from gallium arsenide Practical LEDs began with gallium arsenide, a direct-bandgap III–V semiconductor that emits infrared light efficiently. Rubin Braunstein reported GaAs emission at RCA in 1955, and in 1961 James Biard and Gary Pittman at Texas Instruments found strong infrared emission from GaAs diodes and patented the device, which TI sold from 1962 as the SNX-100, the first commercial LED. ## 1962: Nick Holonyak Jr. and the first visible LED On 9 October 1962 Nick Holonyak Jr. at General Electric made the first practical visible LED. By alloying gallium arsenide with gallium phosphide into GaAsP, he widened the band gap enough to emit red light near 650–700 nm while keeping it direct. He is often called the father of the LED. ## 1968–1980s: LEDs become products Monsanto began mass-producing red GaAsP LEDs in 1968 and supplied Hewlett-Packard, which used them in instrument displays and, from 1972, pocket calculators. Prices fell from hundreds of dollars to cents, and LEDs became the standard indicator light and the glowing digits of early calculators and digital watches. ## 1976: Thomas P. Pearsall and fiber-optic LEDs In 1976 Thomas P. Pearsall engineered indium gallium arsenide phosphide alloys whose emission matched the low-loss wavelengths of glass fiber, around 1.3 and 1.55 micrometers. These high-brightness infrared LEDs powered the first generation of fiber-optic links and remained in short-reach networks, such as 100BASE-FX Ethernet, for decades. ## 1980s–1990s: The brightness race Through the 1980s, AlGaAs heterostructures produced "superbright" red LEDs readable in daylight. In the early 1990s, AlInGaP from Hewlett-Packard and Toshiba brought efficient red, orange, amber and yellow, beating filtered incandescent lamps, so traffic signals and tail lights switched to LEDs. Efficient blue was still missing. ## 1989–1996: The blue LED and white light Gallium nitride had the right band gap for blue light, but it could not be grown as good crystals and nobody could make p-type GaN. Akasaki and Amano solved both problems between 1986 and 1989, and Shuji Nakamura at Nichia made the process manufacturable, launching a bright InGaN blue LED in 1993. ## 2000s–today: The solid-state lighting revolution White LEDs moved into general lighting after Lumileds launched the 1-watt Luxeon in 1999. Haitz's law, a tenfold fall in cost per lumen and twentyfold rise in output per package each decade, held for over twenty years. Efficacy rose from about 5 lm/W in 1996 to a laboratory record of 303 lm/W in 2014. ## What comes next Research is now focused on closing the "green gap" between 530 and 590 nm, reducing efficiency droop at high currents, improving deep-UV LEDs for disinfection, and mass-producing MicroLED screens. New emitters such as perovskite and quantum-dot LEDs, and Li-Fi networking through LED lights, could open the next chapter. --- # How LEDs work URL: https://ledlights.org/how-leds-work/ · Updated: 2026-11-15 **Definition (Electroluminescence):** Electroluminescence is the emission of light by a material in direct response to an electric current. In an LED, current flows forward through a semiconductor p–n junction: electrons and holes meet in the junction and recombine, and each recombination can release one photon whose energy matches the material's band gap. Unlike a filament, an LED needs no heat to make light. ## The p–n junction An LED is a p–n junction: a semiconductor crystal with an n-type side rich in free electrons and a p-type side rich in holes, created by doping, for example with silicon and magnesium in gallium nitride. Light is made where the two sides meet, when electrons and holes are pushed together. ## Recombination and electroluminescence When an electron in the conduction band falls into a hole in the valence band, it releases energy. In radiative recombination that energy leaves as a photon of light, which is electroluminescence; in defect-assisted (Shockley–Read–Hall) or Auger recombination it becomes heat. Good LEDs maximize the radiative path. ## Band gap and wavelength Each photon carries roughly the band gap energy of the light-emitting layer, so the band gap sets the color. The rule is λ (nm) ≈ 1240 ÷ Eg (eV): a 2.76 eV InGaN layer emits 449 nm blue, and 1.98 eV AlInGaP emits 626 nm red. Real LEDs emit bands 15–30 nm wide. ## Semiconductor materials and their colors LED color is set by the semiconductor alloy. Gallium arsenide and AlGaAs emit infrared and deep red, AlInGaP covers red, orange, amber and yellow, InGaN covers violet, blue and green, and AlGaN reaches ultraviolet. Forward voltage rises with band gap, from about 1.2 V for infrared to 3.6 V for blue and more for ultraviolet. Table: LED semiconductor materials, band gaps, colors and forward voltages |Material|Band gap (eV)|Wavelength range|Colors|Typical Vf|Notes| |---|---|---|---|---|---| |GaAs (gallium arsenide)|1.42|850–940 nm|Infrared|1.2–1.5 V|First commercial LED (1962); remotes, optocouplers| |AlGaAs (aluminium gallium arsenide)|1.42–1.9 (direct)|640–880 nm|Deep red, IR|1.5–2.0 V|"Superbright" reds of the 1980s; 660/730/850 nm today| |GaAsP (gallium arsenide phosphide)|1.42–2.26|580–700 nm|Red, orange, yellow|1.8–2.2 V|Holonyak's 1962 red; nitrogen doping for yellow (1972)| |GaP (gallium phosphide)|2.26 (indirect)|555–700 nm|Yellow-green, red|2.0–2.2 V|Classic dim green indicators (GaP:N, 565 nm)| |AlInGaP (aluminium indium gallium phosphide)|1.9–2.3|560–650 nm|Red, orange, amber, yellow|1.9–2.5 V|Today's red and amber; brake lights, traffic signals, RGB| |InGaN (indium gallium nitride)|~2.3–3.3 (in use)|365–550 nm|UV-A, violet, blue, cyan, green|2.7–3.6 V|Blue pump for white LEDs; Nobel Prize 2014| |GaN (gallium nitride)|3.4|~360–370 nm|UV-A|3.2–4.0 V|Barrier and cladding layers; UV-A emitters| |AlGaN / AlN|3.4–6.0|210–360 nm|UV-B, UV-C|4–8 V|Germicidal LEDs; low efficiency| |SiC (silicon carbide)|~3.0–3.3 (indirect)|~470 nm (historic)|Blue|3.0–3.6 V|Round 1907, Losev 1920s, Cree blue 1989; now a substrate| Note: Typical values at room temperature and rated current. Vf depends strongly on the chip design, current and temperature, so always check the datasheet. ## How LEDs make white light No semiconductor emits white directly, so LEDs mix colors. Over 95% of white LEDs use a blue chip under a yellow phosphor, sometimes with red phosphor for warmer, higher-CRI light. Others use a violet chip with full-spectrum phosphors, or mix separate red, green and blue chips for color-changing light. Table: Ways to make white light with LEDs |Method|How it works|Typical CRI|Efficacy|Best for| |---|---|---|---|---| |Blue + YAG:Ce phosphor|450 nm blue chip under a yellow garnet phosphor|Ra 70–80|Highest: 150–230 lm/W|Streetlights, warehouses, offices, budget bulbs| |Blue + green and red phosphors|Adds a nitride red (CASN) phosphor for warm, high-CRI light|Ra 90–98, R9 50–95|High: 120–180 lm/W|Homes, retail, hospitality, healthcare| |Violet pump + full-spectrum phosphors|405–420 nm chip with a red-green-blue phosphor blend, no blue spike|Ra 95–99|Moderate: 80–130 lm/W|Museums, galleries, premium homes| |RGB or RGBW chips|Separate red, green and blue dies mixed in the optics|Ra 20–80 (RGB); 80–90 with a white die|Moderate, limited by the green gap|Color-changing, stage and display lighting| Note: Typical values for current products. Efficacy is at the LED package; fixtures lose a further 10–20% in optics and drivers. ## Lumens, watts and efficacy Watts measure power used; lumens measure visible light produced, weighted by the eye's sensitivity. Efficacy, in lumens per watt, is the key efficiency figure: a 60 W-equivalent LED bulb gives about 800 lumens from 8–9 W. Candela measures intensity in one direction, lux the light falling on a surface. ## Color quality: CCT, CRI and binning LED color quality has three parts: correlated color temperature, which says how warm or cool the white looks; color rendering, measured by CRI and TM-30, which says how naturally colors appear; and binning, which keeps the color of LEDs from different batches consistent. All three appear on good datasheets. Table: MacAdam ellipse steps (SDCM) and visible color difference |Bin size|Visible difference side by side|Typical use| |---|---|---| |1-step|None: indistinguishable|Color-critical display and museum work; rare and costly| |2-step|Barely perceptible, even to trained eyes|Premium architectural fixtures, galleries, long linear runs| |3-step|Slight; usually unnoticed|Quality commercial and residential fixtures| |4-step|Noticeable on uniform white walls|Mid-range products| |5-step|Clearly visible across a row of fixtures|Budget products and many LED strips| |7-step|Obvious mismatch|Roughly the size of an ANSI C78.377 nominal-CCT quadrangle| Note: How large a color difference each MacAdam step size produces between two LEDs of the same nominal CCT, viewed side by side. ## Thermal management LEDs convert much of their input power into heat inside a tiny chip, and that heat must flow through the package, circuit board and heat sink. Junction temperature is critical: higher temperatures immediately reduce light output, shift color, speed up aging and shorten driver life, so good thermal design matters. ## Drivers: constant current vs. constant voltage Because LED current rises exponentially with voltage, every LED needs current limiting. Constant-current drivers regulate the current for series strings, COBs and high-power fixtures; constant-voltage supplies of 12, 24 or 48 V power strips with built-in resistors; and a simple series resistor is enough for low-power indicators. ## Dimming and flicker LEDs dim in two ways: constant-current reduction lowers the DC current without flicker, while pulse-width modulation switches the LED fully on and off and varies the duty cycle. PWM keeps color constant and dims precisely, but at a few hundred hertz it can cause flicker; above about 3 kHz it is low risk. ## Lifetime and reliability LEDs rarely burn out; they fade. Lifetime is quoted as L70, the hours until output drops to 70% of its initial value, based on IES LM-80 tests of at least 6,000 hours projected with TM-21. Well-cooled luminaires last 50,000–100,000 hours, but hot, cheap bulbs may fail in a few thousand. --- # CRI and CCT: the color of LED light URL: https://ledlights.org/physics/cri-and-cct-kelvin-guide/ · Updated: 2026-11-14 **Definition (Color rendering index (CRI)):** The color rendering index (CRI, Ra) is a score of up to 100 for how closely a light source reproduces the colors of standard test samples compared with a reference light of the same correlated color temperature (CCT). CCT, measured in kelvin, describes whether white light looks warm (2,700 K) or cool (6,500 K); CRI describes how faithfully it shows colors. ## Color temperature (CCT) Correlated color temperature, in kelvin, describes whether white light looks warm or cool by comparing it with a glowing blackbody. Lower values look warmer: 2,700 K matches an incandescent bulb, 4,000 K is neutral white and 6,500 K resembles overcast daylight. CCT says nothing about color rendering. Table: LED color temperatures (CCT) and where to use them |CCT|Appearance|Comparable to|Best for| |---|---|---|---| |1,800–2,200 K|Very warm, amber|Candlelight, dimmed incandescent|Restaurants, bars, bedrooms at night, dark-sky outdoor lighting| |2,700 K|Warm white|Incandescent bulb|Living rooms, bedrooms, dining rooms| |3,000 K|Soft warm white|Halogen lamp|Kitchens, bathrooms, hotels, shops, streetlights| |3,500 K|Neutral warm|Some fluorescent tubes|Offices, classrooms, retail| |4,000 K|Neutral white|Cool-white fluorescent|Offices, garages, workshops, hospitals| |5,000 K|Daylight white|Direct midday sun|Color evaluation, art studios, warehouses| |6,500 K|Cool daylight|Overcast sky (D65)|Display calibration, some task lighting; can feel harsh at home| |10,000 K|Bluish|Clear blue sky|Marine aquariums, special effects| ## Color rendering index (CRI, Ra) The color rendering index, Ra, is a score of up to 100 for how closely eight pastel test colors look under a lamp compared with a reference source of the same CCT. Ra 80 is the usual indoor minimum, Ra 90 or more is recommended for homes and shops, and 95+ for color-critical work. ## R9: why deep red matters R9 is the CRI score for a saturated red sample, and it is not included in the Ra average. Many cheap white LEDs score near zero or below, making skin, food and wood look dull. Look for R9 of 50 or more for homes and 90 or more for color-critical work. ## TM-30: fidelity (Rf) and gamut (Rg) TM-30 replaces CRI's eight pastels with 99 color samples and reports two main numbers: Rf, a fidelity score from 0 to 100, and Rg, a gamut score where 100 matches the reference, above 100 is more saturated and below is duller. A color-vector graphic shows which hues shift. ## Recommended CCT and CRI by room Use warm 2,700–3,000 K light with CRI 90+ in living rooms and bedrooms, 3,000–4,000 K with CRI 90+ in kitchens and bathrooms, and 3,500–4,000 K in offices. Shops and galleries benefit from CRI 95+ with high R9, and outdoor lighting should stay at 3,000 K or below. Table: Recommended CCT and CRI for each room and space |Space|CCT|CRI (Ra)|R9|Notes| |---|---|---|---|---| |Living room|2,700–3,000 K|90+|50+|Dim-to-warm for evenings| |Bedroom|2,200–2,700 K|90+|50+|Warm and dimmable; avoid bright cool light at night| |Kitchen|3,000–4,000 K|90+|50+|Food and skin look natural; bright task light on counters| |Bathroom vanity|3,000–4,000 K|90–95+|50+|Even, front-facing light for grooming and makeup| |Home office|3,500–4,000 K|90+|—|Alert, neutral light by day| |Office, classroom|3,500–4,000 K|80–90|—|EN 12464-1 minimum is Ra 80| |Retail: fashion, food|3,000–3,500 K|90–98|80+|Reds and skin tones sell products| |Museum, gallery|2,700–3,500 K|95–98|90+|Rf 90+, minimal UV| |Garage, workshop|4,000–5,000 K|80–90|—|Higher light levels for detail work| |Healthcare examination|3,500–5,000 K|90+|50+|Accurate skin color for diagnosis| |Outdoor, streets|3,000 K or less|70+|—|Shielded fixtures; 2,200–2,700 K near habitats| Note: Starting points; personal preference and daylight matter. Use one CCT per room so fixtures match. ## Color consistency: MacAdam steps and Duv Two LEDs with the same nominal CCT can still look different. MacAdam ellipse steps measure that difference: within 1–2 steps it is invisible, 3 steps is barely noticeable, and 5 or more is obvious side by side. Specify 3-step or tighter for rows of downlights and long linear runs. ## How to read a lighting label Check four things on the box: lumens for brightness, CCT in kelvin for warmth, CRI (and R9 if listed) for color quality, and whether the lamp is dimmable. Three-digit codes are common shorthand: 927 means CRI 90+ at 2,700 K, and 840 means CRI 80+ at 4,000 K. --- # LED drivers and flicker URL: https://ledlights.org/physics/led-drivers-and-flicker/ · Updated: 2026-11-15 **Definition (LED driver):** An LED driver is the power supply that converts mains AC, or a battery or DC bus, into the regulated power an LED needs. Because LED current rises steeply with voltage, the driver holds either the current constant (constant-current drivers) or the voltage constant (constant-voltage drivers, for strips and modules with their own current limiting). ## Why LEDs need a driver An LED's current rises steeply with voltage and its forward voltage falls as it warms, so a fixed voltage can quickly overdrive it. A driver converts mains AC or battery power into a controlled DC current, rectifying, stepping down and regulating it so the LED stays bright, cool and stable. ## Constant current vs constant voltage Constant-current drivers hold a fixed current, such as 350, 700 or 1,050 mA, and let the voltage float; they power LEDs wired in series, like COBs and downlights. Constant-voltage drivers hold a fixed 12, 24 or 48 V for strips and modules that have their own current limiting built in. Table: Constant-current vs constant-voltage LED drivers |Property|Constant current (CC)|Constant voltage (CV)| |---|---|---| |Regulates|Current (e.g. 350, 700, 1,050 mA)|Voltage (12, 24 or 48 V)| |Output voltage|Floats within a window to suit the load (e.g. 9–42 V)|Fixed| |LED wiring|LEDs in series|Strips or modules in parallel| |Current limiting|In the driver|On the strip (resistors or ICs)| |Typical loads|COBs, downlights, high-bays, streetlights, panels|LED strips, signage modules, cabinet lights| |Sizing|Match current; LED string voltage inside the window|Match voltage; load at most 80% of rated watts| |Classic mistake|Connecting a CV strip to a CC driver|Connecting bare LEDs without current limiting| ## Inside a driver: linear, buck and flyback Cheap linear drivers burn off excess voltage and often flicker. Buck converters step mains down efficiently and are common in bulbs, while isolated flyback drivers use a transformer for safety. The best drivers use two stages, power-factor correction followed by a DC-to-DC converter, for low ripple and flicker. ## Power factor, harmonics and inrush Power factor measures how efficiently a driver draws current from the grid; 1.0 is ideal, cheap drivers manage 0.5–0.6 and quality drivers exceed 0.9 with total harmonic distortion under 20%. Many LED drivers also draw a brief inrush current at switch-on that can trip breakers or weld relay contacts. ## How LEDs are dimmed: PWM and CCR Drivers dim LEDs in two ways. Pulse-width modulation switches full current on and off rapidly and varies the on-time, keeping color constant but risking flicker at low frequencies. Constant-current reduction lowers the current itself, which is flicker-free but can shift color and lose control at very low levels. ## Dimming controls: TRIAC, ELV, 0–10 V, DALI and DMX Homes mostly dim with phase-cut wall dimmers, either leading-edge TRIAC or gentler trailing-edge ELV types. Commercial buildings use 0–10 V analog control or digital DALI, which addresses up to 64 drivers per line. Stage and façade lighting runs on DMX512, and smart homes increasingly use wireless protocols. Table: LED dimming control methods compared |Method|How it works|Wiring|Typical use|Watch out for| |---|---|---|---|---| |Leading-edge (TRIAC)|Cuts the start of each AC half-cycle|Existing 2-wire dimmers|Retrofit bulbs in homes|Minimum load, flicker, buzzing, limited range| |Trailing-edge (ELV)|Cuts the end of each half-cycle, gentler on electronics|2-wire; some need a neutral|LED bulbs and fixtures, Europe|Still needs a compatible driver| |0–10 V (1–10 V)|Low-voltage DC signal sets the level|Two extra control wires|Panels, troffers, high-bays|No addressing; separate switching| |DALI / DALI-2|Digital bus, 64 addresses and 16 groups per line (IEC 62386)|2-wire bus, polarity-free|Offices, hospitals, emergency lighting|Needs commissioning| |DMX512 / RDM|512 channels per universe at 250 kbit/s|Shielded twisted pair (RS-485)|Stage, façades, RGB and pixel lighting|Termination and addressing| |Wireless|Zigbee, Bluetooth Mesh, Thread/Matter, Casambi|None beyond power|Smart homes, retrofits|Standby power, interoperability| ## What is LED flicker? Flicker, or temporal light modulation, is a rapid repeated change in light output, usually from mains ripple at 100 or 120 Hz or from low-frequency PWM dimming. Even when invisible, it can cause headaches, eyestrain, stroboscopic effects on moving objects and banding in camera footage. ## Measuring flicker: percent flicker, Pst LM and SVM Percent flicker compares maximum and minimum light output; IEEE 1789 rates it low-risk below 0.08 times the frequency, about 9.6% at 120 Hz. The EU instead uses Pst LM for visible flicker and SVM for stroboscopic effects, requiring Pst LM of 1.0 or less and, since September 2024, SVM of 0.4 or less. Table: LED flicker metrics and limits |Metric|What it measures|Good values|Where it is used| |---|---|---|---| |Percent flicker|(max − min) ÷ (max + min) × 100|Low risk ≤ 0.08 × frequency (9.6% at 120 Hz); no observable effect ≤ 0.0333 × frequency (4% at 120 Hz)|IEEE 1789 (90 Hz to 1.25 kHz; above 3 kHz exempt)| |Flicker index|Area above the mean ÷ total area of one cycle|Lower is better; accounts for waveform shape|Older IES and ENERGY STAR reporting| |Pst LM|Visibility of direct flicker (below ~80 Hz); 1.0 = noticed by half of observers|≤ 1.0|EU Regulation 2019/2020, since September 2021| |SVM|Visibility of the stroboscopic effect (80 Hz–2 kHz)|≤ 0.4 (≤ 0.9 from 2021 to 2024)|EU Regulation 2019/2020, since September 2024| |JA8 modulation|Percent amplitude modulation at full and 20% output|< 30% below 200 Hz|California Title 24, JA8| ## How to avoid flicker, buzzing and ghosting Buy lamps and drivers that publish flicker data, pair them with LED-rated trailing-edge dimmers from the maker's compatibility list, and set the dimmer's low-end trim. Avoid mixing bulb brands on one dimmer. A faint glow when off usually comes from leakage current and is cured with a neutral-wired dimmer or load correction device. --- # LED lifespan: L70, LM-80 and TM-21 URL: https://ledlights.org/physics/led-lifespan-l70-lm80/ · Updated: 2026-11-15 **Definition (L70 lifetime):** L70 is the number of operating hours until an LED's light output falls to 70% of its initial value. Because LEDs usually dim gradually rather than burning out, lifetime is defined by this lumen maintenance threshold, measured under IES LM-80 and projected with ANSI/IES TM-21. ## Lumen maintenance: L70, L80, L90 and B values LEDs rarely burn out; they slowly dim. L70 is the time until light output falls to 70% of its initial value, the point at which most people notice the loss. Ratings such as L70B50 add a B value: the share of units expected to fall below that level by the rated time. Table: LED lifetime ratings: L and B values explained |Rating|Meaning|Typical use| |---|---|---| |L70|Hours until output falls to 70% of initial|General lighting; ENERGY STAR and DLC| |L80|Hours until output falls to 80%|Offices and retail, tighter designs| |L90|Hours until output falls to 90%|Museums, premium and critical lighting| |B50|Half of units below the L value at the rated time|Default (median) when no B value is stated| |B10|Only 10% of units below the L value|Conservative specifications| |C and F values|C: abrupt failures (units that stop working); F: gradual and abrupt combined|IEC 62717 and IEC 62722-2-1, e.g. L80F10| ## LM-80: how LED packages are tested IES LM-80 is the test method for LED packages, arrays and modules: samples run continuously at fixed case temperatures, usually 55 °C, 85 °C and a third chosen by the maker, with light output and color measured at least every 1,000 hours for 6,000 hours or more, and preferably 10,000. ## TM-21: projecting lifetime TM-21 turns LM-80 data into a lifetime projection by fitting an exponential curve to the later test data and extrapolating. Projections are capped at six times the test duration with 20 or more samples, so 10,000 hours of testing supports a claim of at most "L70 greater than 60,000 hours". ## From LED chips to lamps and luminaires LM-80 and TM-21 describe only the LED package. The whole lamp or fixture also depends on how hot its LEDs run and on the driver. IES LM-84 and TM-28 extend testing and projection to complete lamps and luminaires, and in-situ temperature measurement tests confirm the LEDs stay within their tested range. ## Why LEDs fail Most LED products fail because of something other than the LED chips: the driver's electrolytic capacitors dry out, heat degrades phosphors and lenses, sulfur or moisture corrodes silver-plated parts, solder joints crack with thermal cycling, and voltage surges or static destroy components. In series strings, one open LED can darken the whole string. ## How to make LEDs last longer Heat is the main enemy. Choose lamps rated for enclosed fixtures if they will be enclosed, keep heat sinks clear of insulation and dust, and avoid running LEDs at their maximum current. Use surge protection outdoors and quality drivers with 105 °C capacitors. Frequent switching, unlike with fluorescents, barely affects LED life. ## Rated hours in years Divide the rated hours by the hours used per year. A 25,000-hour bulb used three hours a day lasts about 23 years, while a 50,000-hour fixture running 12 hours a day lasts about 11. Real life is shorter in hot, enclosed or poorly ventilated fixtures and with low-quality drivers. Table: LED lifetime in years at typical usage |Rated life|Usage|Hours per year|Years| |---|---|---|---| |15,000 h|3 h/day (home)|1,095|13.7| |25,000 h|3 h/day (home)|1,095|22.8| |25,000 h|8 h/day (kitchen, office)|2,920|8.6| |50,000 h|12 h/day (retail)|4,380|11.4| |50,000 h|Dusk to dawn (streetlight)|~4,100|12.2| |50,000 h|24/7 (parking garage)|8,760|5.7| |100,000 h|24/7 (tunnel, garage)|8,760|11.4| --- # Blue light, sleep and eye safety URL: https://ledlights.org/physics/blue-light-sleep-and-eye-safety/ · Updated: 2026-11-15 **Definition (Blue light):** Blue light is visible light of roughly 400–500 nm. It affects health in two separate ways. Through melanopsin cells in the retina, most sensitive near 490 nm, it shifts the body clock and suppresses melatonin. At very high intensities it can also cause the blue-light hazard, photochemical damage to the retina that peaks near 435–440 nm. ## Two different effects: the body clock and the blue-light hazard Blue light acts on the eye in two separate ways. Melanopsin cells, most sensitive near 490 nm, signal the body clock and suppress melatonin at ordinary indoor light levels. The blue-light hazard is photochemical damage to the retina, peaking near 435–440 nm, which needs long staring at very bright sources such as the sun. ## What the studies show: light, melatonin and sleep Controlled laboratory studies agree that evening light delays the body clock and suppresses melatonin, and that blue-rich light does more per lux. Ordinary room light did so in a 2011 study, and five evenings of reading on an iPad delayed melatonin onset by about 1.5 hours in 2015. Total sleep time changed little. Table: Key studies of evening light, melatonin and sleep |Study|What was tested|Main findings| |---|---|---| |Lockley et al. 2003|6.5 h of 460 nm (blue) or 555 nm (green) light at equal photon density|Blue light delayed the body clock twice as much and caused twice the melatonin suppression| |Gooley et al. 2011|116 adults aged 18–30 in room light (under 200 lux) or dim light (under 3 lux) for the 8 h before bedtime|Room light delayed melatonin onset in 99% of people and shortened melatonin duration by about 90 min| |Chang et al. 2015|12 young adults reading for about 4 h on 5 evenings, on an iPad (about 32 lux at the eye) or a printed book (about 1 lux)|iPad: melatonin onset more than 1.5 h later, 10 min longer to fall asleep, 12 min less REM sleep; total sleep time unchanged| |Phillips et al. 2019|55 adults aged 18–30, 5 h of evening light from 10 to 2,000 lux|Half-maximal melatonin suppression at about 25 lux on average, from 6 to 350 lux between individuals; 10, 30 and 50 lux delayed melatonin onset by 22, 77 and 109 min| |Duraccio et al. 2021|167 adults aged 18–24, 1 h of iPhone use before bed for 7 nights with Night Shift on, off, or no phone|No difference in sleep between the three groups; among those sleeping more than about 7 h, no phone gave the best sleep| ## Warm and cool white compared At the same lux, cool white light stimulates melanopsin about twice as strongly as warm white. From CIE data, a 2700 K LED gives 0.41 melanopic EDI per lux, a 4000 K LED 0.63 and a 6500 K LED 0.85; an incandescent lamp gives 0.50. Halving the brightness halves the melanopic EDI. Table: Melanopic EDI and blue-light hazard per lux of standard light spectra, daylight = 1 (calculated from CIE data) |Light source|CCT|Melanopic EDI per lux|Lux for 10 melanopic EDI|Blue-light hazard per lux| |---|---|---|---|---| |Warm-white LED (LED-B1)|2733 K|0.41|25|0.27| |Incandescent (illuminant A)|2856 K|0.50|20|0.31| |Warm-white LED (LED-B2)|2998 K|0.46|22|0.32| |Neutral-white LED (LED-B3)|4103 K|0.63|16|0.55| |Cool-white LED (LED-B4)|5109 K|0.69|14|0.70| |Cool-white LED (LED-B5)|6598 K|0.85|12|0.90| |Daylight (D65)|6504 K|1.00|10|1.00| ## How much light, and when A 2022 expert consensus recommends at least 250 lux melanopic EDI at eye level during the day, no more than 10 from three hours before bedtime, and no more than 1 in the bedroom while sleeping. Indoors, 10 melanopic EDI is roughly 25 lux of warm-white LED light measured at the eye. Table: Recommended melanopic EDI by time of day (Brown et al. 2022) |When|Melanopic EDI at the eye|Equivalent 2700 K LED light at the eye| |---|---|---| |Daytime|At least 250 lux|About 615 lux, or daylight| |Evening, from 3 h before bed|At most 10 lux|About 25 lux| |Sleeping|At most 1 lux|About 2.5 lux, or darkness| |At night, if light is needed|At most 10 lux|About 25 lux| ## Screens and night modes A tablet at full brightness and reading distance gave about 32 lux at the eye in a 2015 study, similar to typical evening room light. Night modes warm the colors but do not dim the screen, and in a 2021 trial Night Shift did not improve sleep. Lower brightness and less evening use matter more. ## The blue-light hazard and IEC 62471 risk groups IEC 62471 classifies lamps by how long a person could stare into them before reaching the blue-light hazard limit: exempt (RG0) beyond 10,000 seconds, low risk (RG1) 100 to 10,000 seconds, moderate (RG2) 0.25 to 100 seconds, and high (RG3) under 0.25 seconds. Household white LED lamps are normally RG0 or RG1. Table: IEC 62471 blue-light hazard risk groups |Risk group|Staring time to reach the limit|Meaning in IEC 62471| |---|---|---| |RG0, exempt|More than 10,000 s (2.8 h)|No photobiological hazard| |RG1, low risk|100–10,000 s|No hazard under normal behavioral limits on exposure| |RG2, moderate risk|0.25–100 s|No hazard because people look away from very bright light| |RG3, high risk|Under 0.25 s|Hazardous even for a momentary or brief exposure| ## Children's and older eyes Children's eyes let more blue light reach the retina, and their body clocks respond more strongly to evening light. The CIE advises against blue indicator lights in toys, and SCHEER flags bright blue LEDs in toys for children under three. With age the lens yellows, so the same lamp gives older eyes less melanopic stimulus. ## Do LEDs cause macular degeneration? No human study has shown that household LED lighting or screens cause age-related macular degeneration. The CIE calls such claims speculative and the EU's SCHEER found no evidence of harm in normal use. France's ANSES disagreed in 2019, concluding that chronic blue-rich exposure raises the risk, while rating warm-white home LEDs low risk. ## Do blue-light glasses help? The evidence does not support blue-blocking glasses for eye strain or eye health. A 2023 Cochrane review of 17 trials found they may not reduce eye strain from computer use, with sleep effects unclear. The American Academy of Ophthalmology does not recommend them; it suggests the 20-20-20 rule for tired eyes. ## Flicker and glare Some LED products flicker at twice the mains frequency, 100 or 120 Hz. Most people cannot see it directly, but it can show up as stroboscopic effects and has been linked to headaches and eye strain. SCHEER lists flicker at 100 Hz and above as a potential concern; IEEE 1789 and EU rules set limits. ## Practical guidance Get bright light, ideally daylight, during the day. In the three hours before bed, use warm 2700 K or warmer light, dimmed to around 25 lux at the eye or less. Turn screen brightness down, keep the bedroom dark, choose flicker-free products, and never stare into bare high-power LEDs or flashlights. --- # Types of LEDs URL: https://ledlights.org/types/ · Updated: 2026-11-15 **Definition:** LEDs are grouped by package (how the chip is housed and mounted: through-hole, surface-mount, chip-on-board, chip-scale), by power class (indicator, mid-power, high-power), by function (lighting, display, sensing) and by emission (visible, infrared, ultraviolet, multi-color, addressable). The package largely determines how much heat an LED can shed, and therefore how bright and efficient it can be. ## Through-hole (DIP) LEDs: 3 mm and 5 mm Through-hole, or DIP, LEDs are the classic epoxy-bullet LEDs with two wire legs, mainly 3 mm (T-1) and 5 mm (T-1¾). They run at about 20 mA and 0.1 W or less, and because heat can leave only through the thin leads, they suit indicators, hobby electronics and large-pixel signs rather than lighting. ## SMD (surface-mount) LEDs Surface-mount (SMD) LEDs sit flat on the circuit board and are soldered to copper pads by machine. Most lighting types are PLCC packages, a lead frame in a reflective white housing filled with phosphor silicone, and their thermal pads shed heat far better than DIP LEDs, so they dominate bulbs, tubes, panels and strips. Table: SMD LED package sizes, power and output |Package|Size (mm)|Typical power|Typical flux (white)|Thermal pad|Typical use| |---|---|---|---|---|---| |3528|3.5 × 2.8 × 1.9|0.06–0.08 W (20 mA)|5–8 lm|No|Early low-power strips, backlights, indicators| |2835|2.8 × 3.5 × 0.8|0.2 W (60 mA); 0.5 W and 1 W versions|20–30 lm at 0.2 W; up to ~130 lm at 1 W|Yes (large)|Bulbs, tubes, panels, high-efficiency strips| |3030|3.0 × 3.0 × 0.55|0.5–2 W|60–250 lm|Yes|High-bays, streetlights, horticulture boards| |5050|5.0 × 5.0 × 1.6|0.2–0.24 W (3 × 20 mA)|18–24 lm|No (6 leads)|RGB and addressable strips, signage| |5630|5.6 × 3.0 × 0.9|0.5 W (150 mA)|45–60 lm|Yes (centre)|Panels, troffers, T8 tubes| |5730|5.7 × 3.0 × 0.8|0.5–1 W|50–60 lm at 0.5 W|Yes|Corn bulbs, panels, tubes| Note: Typical white mid-power SMD LEDs. Output varies with CCT, CRI, current and manufacturer. ## Inside the package: DIP vs. SMD vs. COB DIP, SMD and COB packages differ mainly in how heat leaves the die. A DIP LED sheds heat through a thin lead, an SMD LED through a metal pad soldered to the board, and a COB through a thick metal or ceramic substrate bolted directly to a heat sink. ## COB and MCOB LEDs Chip-on-board LEDs bond dozens to hundreds of bare dies directly onto an aluminum or ceramic substrate under one continuous phosphor layer, creating a single uniform light-emitting surface 6–30 mm across. Rated from 3 to over 200 W, they power downlights, spotlights, high-bays and stage lights, and need generous heat sinks. ## CSP (chip-scale package) and flip-chip LEDs A chip-scale package LED is no more than 20% larger than its die: a flip-chip die solders directly to the board, with phosphor applied as a thin film and no lead frame, bond wires or housing. CSPs are tiny, run cool and suit backlights, headlamps, camera flashes and dense arrays. ## Filament LEDs (COG) LED filaments are narrow glass or sapphire strips carrying 20–30 tiny dies in series, coated with phosphor so they glow in every direction, recreating the look of a clear Edison bulb. A four-filament lamp gives about 400–470 lumens, at 100–160 lumens per watt, but enclosed fixtures shorten their life. ## High-power LEDs (1 W to 100 W+) High-power LEDs drive a single large die, usually 1 mm square or more, at 350 mA to 3 A in ceramic or metal-slug packages with very low thermal resistance. Starting with the 1999 Luxeon, they became standard in flashlights, headlamps and floodlights, and always need a constant-current driver and heat sink. ## OLED: organic light-emitting diodes OLEDs replace crystalline semiconductors with organic molecule layers only 100–500 nm thick, deposited on glass or flexible plastic. Every sub-pixel makes its own light and can switch fully off, giving perfect blacks, which is why OLED dominates flagship phones and premium TVs despite fast-aging blue emitters and burn-in risk. ## QLED and quantum-dot displays QLED is a marketing name, mainly Samsung's, for LCD TVs with a quantum-dot layer; they are not self-emissive. A blue LED backlight excites 2–10 nm nanocrystals that emit pure red and green, giving wide color gamut and high brightness. True electroluminescent quantum-dot LEDs are still in development. ## Mini-LED Mini-LED is an LCD backlight made of thousands of LEDs 50–200 µm across, grouped into hundreds or thousands of local-dimming zones that follow the image. It delivers HDR highlights of 1,000–2,000+ nits and deep blacks without burn-in, though bright objects on dark backgrounds can show faint blooming halos. ## MicroLED MicroLED displays build every sub-pixel from its own microscopic inorganic LED, usually under 50 µm. They combine OLED's perfect blacks with inorganic LEDs' brightness and decades-long life, but a 4K screen needs about 24.9 million working dies placed by mass transfer, so today's MicroLED screens remain extremely expensive. ## Infrared LEDs: 850 nm vs. 940 nm Infrared LEDs made from GaAs and AlGaAs emit mainly between 700 and 1,000 nm. 850 nm parts show a faint red glow but give silicon cameras longer night-vision range, while 940 nm parts are invisible and suit remote controls, covert cameras and sensors. They are rated in milliwatts, not lumens. Table: Infrared LEDs: 850 nm vs. 940 nm ||850 nm|940 nm| |---|---|---| |Visibility|Faint dull-red glow visible to the eye|Invisible ("no-glow", covert)| |Silicon camera sensitivity|Higher; longer night-vision range|Roughly 40–60% lower; shorter range for the same power| |Sunlight interference|More|Less (atmospheric water absorbs near 940 nm)| |Typical uses|CCTV and dash-cam illuminators, PBM therapy, machine vision, short fiber links|TV and AC remotes, proximity and gesture sensors, covert cameras, pulse oximetry, face-recognition flood illumination| ## Ultraviolet LEDs: UV-A, UV-B and UV-C UV LEDs are made from InGaN for near-UV and AlGaN for shorter wavelengths. UV-A at 365–405 nm cures inks, resins and nail gel; UV-B at 280–315 nm treats skin conditions; and UV-C at 255–280 nm disinfects water, air and surfaces, although UV-B and UV-C efficiency is only a few percent. Table: Ultraviolet LED bands, wavelengths and uses |Band|Range|Common LED wavelengths|Uses|Efficiency| |---|---|---|---|---| |UV-A|315–400 nm|365, 385, 395, 405 nm|Curing of inks, adhesives, coatings and nail gel; 3D-printer resin; fluorescence, forensics, counterfeit detection; insect traps|WPE 20–60%| |UV-B|280–315 nm|295–311 nm|Phototherapy (psoriasis, vitiligo), plant UV-B research, vitamin D studies, sensing|WPE ~1–5%| |UV-C|100–280 nm|255–280 nm (265 and 275 most common)|Germicidal disinfection of water, air and surfaces; DNA/RNA damage stops microbe replication; spectroscopy|WPE ~2–10%| ## Addressable LEDs: WS2812B, SK6812 and APA102 Addressable LEDs such as the WS2812B, SK6812 and APA102 contain a tiny driver chip beside their red, green and blue dies. Each LED reads its own color from a data line and passes the rest along, so every pixel on a strip can show a different color under microcontroller or WLED control. Table: Addressable LED chips: WS2812B, WS2815, SK6812 and APA102 |Chip|Interface|Colors|Voltage|PWM rate|Notes| |---|---|---|---|---|---| |WS2812B|1-wire, 800 kbit/s, timing-critical|RGB, 24-bit (GRB order)|5 V|~0.4–2 kHz|The "NeoPixel" standard; ~60 mA at full white per pixel| |WS2813 / WS2815|1-wire + backup data line|RGB|5 V / 12 V|~2 kHz|A dead pixel doesn't break the chain; 12 V reduces voltage drop| |SK6812 (RGBW)|1-wire, WS2812-compatible timing|RGB + white (warm, neutral or cool), 32-bit|5 V|~1 kHz|A real white die gives far better whites and pastels| |APA102 / SK9822|2-wire SPI (data + clock)|RGB + 5-bit global brightness|5 V|~19–20 kHz (APA102)|Fast, timing-tolerant, flicker-free on camera, ideal for POV| ## Bi-color, tri-color, RGB, RGBW and RGBCCT Multi-color LEDs put several dies in one package. Bi-color and tri-color types show status states, RGB mixes millions of colors, RGBW adds a phosphor-white die for real whites, CCT or tunable white blends warm and cool white, and five-channel RGBCCT combines full color with tunable white. ## Master comparison table Across LED types, mid-power SMD 2835 and 3030 packages lead white-light efficacy at 120–220 lumens per watt, COBs offer the highest CRI options, and high-power and CSP emitters handle heat best. Legacy incandescent bulbs manage only 10–17 lumens per watt; the comparison page sorts every type side by side. --- # SMD 2835 vs 5050 vs 3030 URL: https://ledlights.org/types/smd-2835-vs-5050-vs-3030/ · Updated: 2026-11-15 **Definition (SMD LED):** A surface-mount device (SMD) LED is an LED die in a small rectangular package that is soldered flat onto a circuit board instead of through holes. Its four-digit name, such as 2835, 3030 or 5050, gives the package footprint in tenths of a millimetre, not its power, brightness or quality. ## What the numbers mean An SMD LED's four-digit name is its footprint in tenths of a millimetre: a 2835 measures 2.8 × 3.5 mm, a 3030 is 3.0 × 3.0 mm and a 5050 is 5.0 × 5.0 mm. The name says nothing about power, brightness, color quality or who made the chip inside. ## Side-by-side specifications For white light, 2835 and 3030 packages are the most efficient, at roughly 120–220 lumens per watt, because a large thermal pad pulls heat into the board. 5050 packages hold three dies and suit RGB. 3528 and 5630 are older designs that are now mostly found in budget strips and panels. Table: SMD 2835, 3030, 5050, 3528 and 5630 LED packages compared |Package|Size (mm)|Dies|Typical power|White efficacy|Heat path|Best for| |---|---|---|---|---|---|---| |3528|3.5 × 2.8|1|0.06–0.1 W (20 mA)|60–100 lm/W|Small leads; plastic body|Low-output strips, backlights| |2835|2.8 × 3.5|1–2|0.2–1 W (60–300 mA)|120–220 lm/W|Large exposed thermal pad|Bulbs, tubes, panels, white strips| |3030|3.0 × 3.0|1|0.2–2 W (65–600 mA)|150–220 lm/W|Thermal pad; heat-resistant EMC body|High-bays, streetlights, grow lights| |5050|5.0 × 5.0|3|0.2–0.3 W (3 × 20 mA)|70–110 lm/W|Three lead pairs; plastic body|RGB, RGBW and addressable strips| |5630 / 5730|5.6–5.7 × 3.0|1|0.5 W (100–150 mA)|100–150 lm/W|Thermal pad|Panels, troffers, tubes, corn bulbs| Note: Typical values for white mid-power LEDs from reputable makers. Budget parts are often rated optimistically. ## SMD 2835: the efficient white workhorse The 2835 is the workhorse of white LED lighting. It packs one or two dies above a large exposed thermal pad, runs at 0.2 to 1 watt, and reaches 120–220 lumens per watt in good versions. It dominates LED bulbs, tubes, panels and efficient white strips, including high-CRI grades. ## SMD 3030: square, robust and efficient The 3030 is a square, 3 × 3 mm mid-power package, usually molded from heat-resistant EMC rather than plastic. It tolerates higher current and temperature than a 2835, so it is the usual choice for high-bays, streetlights and horticulture boards, where efficiency and long life matter most. ## SMD 5050: three dies for color A 5050 is a 5 × 5 mm package with three separate dies, each normally driven at about 20 mA. Fitted with red, green and blue dies it is the standard RGB LED, and with a built-in controller it becomes the WS2812B. White 5050s are less efficient than 2835s. ## 3528, 5630 and other packages The 3528 was the original strip LED of the 2000s: low power, around 0.06–0.1 watt, with no large thermal pad. The 5630 and 5730 are rectangular 0.5 watt chips that were popular in early panels and corn bulbs. Both have largely given way to 2835 and 3030 packages. ## Thermal pads and why they matter A thermal pad is a metal area under the LED die that conducts heat straight into the circuit board's copper. Lower junction temperature means more light, stable color and longer life, so a package with a large pad can be driven harder and still outlast one without. ## Which chip for LED strips? For white LED strips, choose 2835 chips at 120 or more per metre, ideally 24 V and CRI 90+. Choose 5050 for RGB or RGBW color, addressable 5050 for effects, and dotless COB strips where the strip is visible or reflected in glossy surfaces. Table: LED strip chips: density, power and output per metre |Strip type|LEDs per metre|Power per metre|Typical output|Notes| |---|---|---|---|---| |3528 white|60 / 120|4.8 / 9.6 W|300–800 lm/m|Low-cost accent; older designs| |2835 white|60–240|6–20 W|600–2,200 lm/m|Best efficacy and CRI options| |5050 white|30 / 60|7.2 / 14.4 W|500–1,400 lm/m|Bright, less efficient| |5050 RGB|30 / 60|7.2 / 14.4 W|200–600 lm/m (all on)|Color mixing; poor whites| |WS2812B (5 V)|30 / 60 / 144|9 / 18 / 43 W at full white|—|Pixel effects; inject power every 1–2 m| |COB (dotless)|320–528 dies|8–15 W|800–1,500 lm/m|No visible dots; runs warm| Note: Typical values at full output. Real strips vary widely; check the maker's lumen and wattage data. ## Which one should you choose? Pick the package by job, not by number. Use 2835 for bulbs, tubes, panels and white strips; 3030 for high-power fixtures and grow lights; 5050 for RGB and addressable effects. When one tight beam or a single shadow matters, skip SMD and use a COB or high-power LED. --- # COB vs SMD vs CSP URL: https://ledlights.org/types/cob-vs-smd-vs-csp/ · Updated: 2026-11-14 **Definition (Chip-on-board (COB) LED):** A chip-on-board (COB) LED mounts many bare LED dies directly on a metal or ceramic substrate and covers them with one continuous phosphor layer, so they act as a single bright light-emitting surface. It contrasts with SMD LEDs, which package each die separately, and CSP (chip-scale package) LEDs, which remove the package almost entirely. ## How each package is built An SMD LED packages each die on a lead frame inside a molded cup. A COB bonds dozens of bare dies directly to a metal or ceramic board under one phosphor layer. A CSP removes the package entirely: a flip-chip die is coated with phosphor and soldered straight to the board. ## COB vs SMD vs CSP at a glance Mid-power SMD LEDs give the lowest cost per lumen and spread heat across many small sources. COB gives one bright, uniform surface with a single crisp shadow but concentrates heat. CSP is the smallest and has the shortest heat path, which suits compact optics, headlamps and backlights. Table: COB vs SMD vs CSP LED packages compared |Property|SMD (mid-power)|COB|CSP| |---|---|---|---| |Construction|Packaged die on a lead frame|Many bare dies on one substrate|Flip-chip die with phosphor, no package| |Size|2–6 mm per package|6–30+ mm emitting surface|1–1.5 mm| |Power per unit|0.1–1 W (1–3 W high-power)|3–200 W+|0.2–3 W| |Efficacy|150–220 lm/W|100–180 lm/W|130–200 lm/W| |Heat path|Thermal pad to board|Substrate straight to heat sink|Direct solder to board (shortest)| |Beam and shadows|Many points; multi-shadows without a diffuser|One source; single crisp shadow|Tiny, intense point for small optics| |Color uniformity|Good with tight binning|Excellent across the surface|Good; edges can look bluish| |Cost per lumen|Lowest|Low to moderate|Moderate| |Typical uses|Bulbs, tubes, panels, strips, high-bays|Downlights, spots, track, stage|Headlamps, flashes, backlights, dense arrays| Note: Typical values for current white LEDs. ## Heat: where the watts go Roughly half or more of the electrical power entering a white LED leaves as heat at the junction. SMD arrays spread that heat across a board, COBs concentrate tens of watts in a few square centimetres, and CSPs pass it through the shortest path, straight into the circuit board. ## Beam, shadows and glare A COB behaves like one bright disc, so it casts a single crisp shadow and pairs well with reflectors for clean spot beams. SMD arrays act as many points and can cast multiple shadows without a diffuser. CSPs are tiny, intense points that let designers use very small optics. ## Reliability and failure modes All three last for tens of thousands of hours when kept cool and driven correctly. Their weak points differ: SMD housings can yellow and silver lead frames can tarnish, COB strings can fail as a group, and CSP solder joints carry all the mechanical stress because there are no leads. ## COB and CSP LED strips COB LED strips pack 320 to more than 500 tiny dies per metre under a continuous phosphor line, giving a smooth, dotless line of light without a diffuser. They look best in coves and glossy reflections, but are usually slightly less efficient and run warmer than a quality 2835 strip. ## Which package should you choose? Choose COB for spotlights, track and museum lighting where one crisp beam matters. Choose mid-power SMD for bulbs, tubes, panels and high-bays where cost per lumen and efficiency matter. Choose CSP or high-power ceramic LEDs for compact optics such as headlamps, flashlights and backlights. --- # OLED vs QLED vs Mini-LED vs MicroLED URL: https://ledlights.org/types/oled-vs-qled-vs-miniled-vs-microled/ · Updated: 2026-11-14 **Definition (Self-emissive display):** A self-emissive display makes light in every sub-pixel, so each pixel can switch fully off for true black. OLED and MicroLED screens are self-emissive. QLED and Mini-LED TVs are LCDs, which filter light from an LED backlight behind the panel. ## Backlit vs self-emissive QLED and Mini-LED TVs are LCDs: an LED backlight shines through liquid crystals that block or pass light. OLED and MicroLED screens are self-emissive: every sub-pixel makes its own light and can switch fully off. That difference drives most trade-offs in contrast, brightness, burn-in and price. ## OLED OLED panels use thin organic layers that glow when current flows, one emitter per sub-pixel. They offer perfect black, wide viewing angles, very fast response and thin, flexible designs. Their limits are lower full-screen brightness than the best LCDs and a risk of burn-in from static images. ## QLED (quantum-dot LCD) A QLED TV is an LCD with a blue LED backlight and a film of quantum dots, nanocrystals that convert blue light into very pure red and green. That gives bright images and a wide color gamut at a lower price, but black levels depend on the backlight's local dimming. ## Mini-LED Mini-LED is an LCD backlight made of thousands of tiny LEDs grouped into hundreds or thousands of dimming zones. Each zone follows the picture, so blacks get deeper and highlights reach 1,000–3,000+ nits. The trade-off is blooming: faint halos around bright objects on dark backgrounds. ## MicroLED MicroLED builds every sub-pixel from a microscopic inorganic LED, combining OLED-style perfect blacks with very high brightness, efficiency and lifetime, and no burn-in. It is extremely expensive because millions of tiny dies must be grown, tested, transferred and repaired, so it is limited to luxury screens and modular walls. ## Side-by-side comparison OLED and MicroLED win on black level and viewing angle; Mini-LED and MicroLED win on peak brightness; QLED wins on price. Only OLED carries a burn-in risk. For most buyers the real choice is OLED for dark rooms versus Mini-LED for bright rooms, with MicroLED still a luxury. Table: OLED vs QLED vs Mini-LED vs MicroLED compared |Property|OLED|QLED|Mini-LED|MicroLED| |---|---|---|---|---| |Light source|Organic emitter per sub-pixel|Blue LED backlight + quantum dots + LCD|Thousands of tiny LEDs in dimming zones + LCD|Inorganic micro-LED per sub-pixel| |Black level|Perfect|Grey without local dimming|Very deep; some blooming|Perfect| |Peak HDR brightness|~1,000–2,000+ nits (small areas)|~500–1,500 nits|~1,000–3,000+ nits|Several thousand nits| |Viewing angle|Excellent|Fair (VA) to good (IPS)|Fair to good|Excellent| |Burn-in|Possible with static content|None|None|None| |Motion response|~0.1 ms|Several ms|Several ms|Microseconds| |Price|$$–$$$|$–$$|$$|$$$$$| |Best for|Dark-room movies, gaming, phones|Bright rooms on a budget|Bright-room HDR, monitors, laptops|Luxury screens, modular walls, AR| Note: Typical values for current televisions; phones and monitors differ. ## Which display technology should you choose? Choose OLED for movies and gaming in dim rooms, Mini-LED for bright living rooms and HDR on a budget, and a basic QLED or LED-backlit LCD when price matters most. For screens showing static content all day, avoid OLED; MicroLED suits luxury installations and large modular walls. ## What comes next Next come tandem OLEDs in laptops and tablets, more efficient blue OLED emitters, quantum-dot LEDs driven directly by current, and cheaper MicroLED through better mass transfer. MicroLED microdisplays for augmented-reality glasses are the nearest mass market, while affordable MicroLED televisions remain a goal for the late 2020s and beyond. --- # LED applications URL: https://ledlights.org/applications/ · Updated: 2026-11-15 **Definition:** LEDs are now the default light source for almost every application, because they are efficient (100–220 lm/W), long-lived, instantly controllable, small and available in any wavelength from UV-C to infrared. Each application values a different mix of these strengths, so the right LED for a grow room, a headlamp or a living room is very different. ## Residential lighting In homes, LEDs replace every traditional bulb shape, from A19 table-lamp bulbs and BR30 recessed floods to GU10 and MR16 spots, and add strip lighting for coves and cabinets. Choose by lumens, keep one color temperature per room, use CRI 90+ where color matters, and pair dimmable lamps with LED-rated dimmers. ## Commercial, industrial and municipal Commercial, industrial and municipal lighting switched early to LEDs because it runs for long hours. Offices replace fluorescent troffers with panels and tubes, warehouses swap metal-halide high-bays for LED, and cities convert streetlights and traffic signals, typically cutting lighting energy by 50–70% with payback in one to three years. ## Specifying LED lighting: lux, beam angle and IP rating Specify LED lighting with three numbers: target illuminance in lux, such as 300–500 lux for offices and classrooms; a beam angle that suits mounting height and spacing; and an IP rating matched to the location, such as IP44 near splashing water and IP65 or higher outdoors. Table: Recommended illuminance (lux) by space and task |Space or task|Lux|Foot-candles| |---|---|---| |Corridors, stairs, parking garages|50–150|5–15| |Living rooms and bedrooms (ambient)|100–300|10–30| |Warehouses and storage aisles|100–300|10–30| |Classrooms|300–500|30–50| |Kitchen countertops, reading, bathroom mirrors|300–750|30–70| |Offices and computer work|300–500|30–50| |Retail sales floors|300–750|30–70| |Detailed assembly, drawing, inspection|750–1,500|70–140| |Hospital examination|1,000|~90| |Professional sports, broadcast (vertical)|1,500–3,000+|140–280+| |Surgical field (IEC 60601-2-41)|40,000–160,000|3,700–15,000| Note: Typical maintained illuminance on the task plane. Check local codes and standards for specific projects. Table: LED beam angles and typical uses |Beam angle|Name|Pool at 3 m|Typical use| |---|---|---|---| |10–15°|Narrow spot|0.5–0.8 m|Artwork, sculptures, high ceilings, façade grazing| |24–25°|Spot|~1.3 m|Accent lighting, retail displays, kitchen islands| |36–40°|Narrow flood|1.9–2.2 m|General downlighting in homes, track lighting| |60°|Flood|~3.5 m|Ambient downlights, low ceilings, garages| |90–120°|Wide flood|6–10 m|Panels, troffers, high-bays in open areas, strips| Table: IP ratings for LED fixtures (IEC 60529) |Rating|Solids|Water|Typical LED use| |---|---|---|---| |IP20|Fingers (≥12.5 mm)|None|Indoor dry locations, drivers in ceilings| |IP44|Wires (≥1 mm)|Splashing from any direction|Bathrooms outside the shower zone, covered porches| |IP54|Dust-protected|Splashing|Workshops, sheltered outdoor fixtures| |IP65|Dust-tight|Low-pressure water jets|Outdoor walls and soffits, shower ceilings, covered parking| |IP66|Dust-tight|Powerful water jets|Floodlights, streetlights, food-processing plants| |IP67|Dust-tight|Temporary immersion (up to 1 m, 30 min)|In-ground uplights, outdoor strips, pathway lights| |IP68|Dust-tight|Continuous immersion (conditions set by maker)|Pool, pond, fountain and underwater lights| |IP69K|Dust-tight|High-pressure, high-temperature washdown|Vehicle lamps (ISO 20653), food and beverage plants| ## Displays and signage LEDs now create nearly every modern screen. Phones and watches use self-emissive AMOLED, televisions use LED-backlit LCDs, quantum-dot "QLED," Mini-LED or OLED, and stadium boards, billboards and virtual-production stages use direct-view LED video walls rated by pixel pitch and brightness in nits. ## Automotive lighting LEDs now light almost every part of a car: headlamps, daytime running lights, brake lights, turn signals and interiors. They react in under a millisecond, can last the life of the vehicle, allow compact styled lamps and matrix high beams, and define brand identity through signature light shapes. ## Aviation Airports use LED runway edge, centerline, taxiway and approach lights, which save energy and greatly reduce maintenance. Aircraft use LEDs for navigation lights, red on the left wingtip and green on the right, anti-collision strobes, landing lights and cabin mood lighting, and towers and wind turbines use LED obstruction lights. ## Marine Boats must show navigation lights defined by the COLREGs: a white masthead light over 225°, red port and green starboard sidelights over 112.5° each, and a white sternlight over 135°. Certified LED navigation lights meet these arcs and ranges while drawing a fraction of the current, which matters on battery-powered boats. ## Horticulture (grow lights) Grow lights are measured in photons, not lumens. PPFD, in micromoles per square meter per second, is the light reaching the canopy, and the daily light integral is PPFD × hours × 0.0036. The best LED grow lights reach 2.7–3.1 µmol/J, far above the 1.7–1.9 of high-pressure sodium. Table: Grow light PPFD, photoperiod and DLI targets by crop |Crop / stage|PPFD (µmol/m²/s)|Photoperiod|DLI (mol/m²/day)| |---|---|---|---| |Seedlings, clones, microgreens|100–300|16–18 h|6–15| |Lettuce and leafy greens|200–400|16–18 h|12–17| |Herbs (basil)|300–500|16 h|15–25| |Tomatoes, peppers, cucumbers|400–700|14–18 h|20–30| |High-light crops, flowering|600–1,000+|12 h|30–45+| Note: Typical targets; actual needs vary with cultivar, CO₂, temperature and growth stage. ## Medical and health LEDs are used throughout medicine: red and near-infrared light for photobiomodulation, 460–490 nm blue for newborn jaundice, high-CRI white for surgical and examination lights, red and infrared pairs in pulse oximeters, blue for dental curing and UV-C for disinfection. They run cool, last long and allow precise wavelengths. ## Telecom and sensing Because LEDs switch millions of times per second, they carry data as well as light: in early and short-reach fiber links, plastic optical fiber in cars and audio gear, and Li-Fi networks. LEDs also power optocouplers, smoke detectors, proximity sensors, optical mice and strobed machine-vision lighting. ## Stage, DJ and entertainment lighting Stage, club and DJ lighting went almost entirely LED in the 2010s. RGBW and RGBA wash lights mix saturated colors without gels, moving heads use 100–1,000 W white LED engines, and addressable pixel bars are mapped like video, all controlled over DMX512, Art-Net or sACN. High PWM frequencies prevent flicker on camera. --- # LED bulb shapes and base types URL: https://ledlights.org/guides/led-bulb-shapes-and-bases/ · Updated: 2026-11-15 **Definition (Lamp base):** A lamp base (or cap) is the part of a bulb that fits the socket and carries the electricity, identified by a code such as E26 (Edison screw, 26 mm) or GU10 (twist-lock with pins 10 mm apart). The bulb shape code, such as A19 or PAR38, describes the glass or housing: a letter for the shape and a number for its diameter. ## Bulb shape codes A bulb code is a letter for the shape followed by the diameter at its widest point, in eighths of an inch in North America: an A19 is the classic bulb shape, 19 eighths or about 2⅜ inches across. Europe uses millimeters instead, so the same shape is called A60. Table: LED bulb shapes: codes, diameters and uses |Code|Shape|Diameter|Also called|Typical base|Typical use| |---|---|---|---|---|---| |A19|Classic household bulb|2⅜ in / 60 mm|A60|E26, E27, B22d|Table lamps, ceiling fixtures| |A21|Larger classic bulb|2⅝ in / 67 mm|A67|E26, E27|100 W and brighter equivalents| |ST19|Vintage teardrop (filament style)|2⅜ in / 60 mm|Similar to ST64|E26, E27|Exposed decorative pendants| |G25|Globe|3⅛ in / 80 mm|G80|E26, E27|Bathroom vanity strips, pendants| |G40|Large globe|5 in / 125 mm|G125|E26, E27|Statement pendants| |B11|Blunt-tip candle|1⅜ in / 35 mm|C35|E12, E14|Chandeliers, wall sconces| |CA10|Flame-tip candle|1¼ in / 32 mm|Candle, flame tip|E12, E14|Decorative chandeliers| |BR30|Bulged reflector, soft beam|3¾ in / 95 mm|Similar to R95|E26, E27|5–6 in recessed cans| |BR40|Bulged reflector, soft beam|5 in / 127 mm|Similar to R125|E26, E27|Large cans, high ceilings| |PAR20|Parabolic reflector, controlled beam|2½ in / 64 mm|PAR20|E26, E27|Track and accent lighting| |PAR30|Parabolic reflector, controlled beam|3¾ in / 95 mm|PAR30 (long or short neck)|E26, E27|Track lights, retail, recessed| |PAR38|Parabolic reflector, controlled beam|4¾ in / 121 mm|PAR38|E26, E27|Outdoor floodlights, high ceilings| |MR16|Multifaceted reflector, compact spot|2 in / 51 mm|MR16|GU5.3 (12 V)|Accent, landscape and display lighting| |GU10 lamp|Compact spot, mains voltage|2 in / 50 mm|PAR16|GU10|Kitchen and track spotlights| |T8|Linear tube|1 in / 26 mm|T26|G13|Offices, garages, workshops| |T5|Slim linear tube|⅝ in / 16 mm|T16|G5|Slim fixtures, coves, high-bays| ## Lamp base codes The base code gives the type and size: E means Edison screw and the number is the diameter in millimeters, so E26 is the standard North American base and E27 the European one. B is bayonet, G and GU are two-pin bases, and the number after them is the pin spacing. Table: LED lamp bases: codes, sizes and where they are used |Base|Type|Size|Region or voltage|Typical lamps| |---|---|---|---|---| |E26 (medium)|Edison screw|26 mm|North America, 120 V|A19, BR30, PAR38| |E27|Edison screw|27 mm|Europe and most of the world, 230 V|A60, globes, reflectors| |E12 (candelabra)|Edison screw|12 mm|North America|Candle bulbs, night lights| |E14 (small Edison)|Edison screw|14 mm|Europe|Candle, golf-ball and appliance lamps| |E17 (intermediate)|Edison screw|17 mm|North America|Appliance and ceiling-fan lamps| |E39 / E40 (mogul)|Edison screw|39–40 mm|Worldwide|Streetlights, high-bays, corn lamps| |B22d|Bayonet, two contacts|22 mm|UK, Ireland, Australia, India|Household bulbs| |B15d|Bayonet, two contacts|15 mm|UK and Europe|Small decorative and appliance lamps| |GU10|Twist-lock, two pins|10 mm pin spacing|Mains voltage|Spotlights| |GU5.3|Bi-pin|5.33 mm pin spacing|12 V|MR16 spotlights| |G9|Looped bi-pin|9 mm pin spacing|Mains voltage|Capsule lamps in small fixtures| |G4 / GY6.35|Bi-pin|4 or 6.35 mm pin spacing|12 V|Capsule lamps in cabinet and landscape lights| |GU24|Twist-lock, two pins|24 mm pin spacing|North America, 120 V|Energy-code fixtures that cannot take incandescent bulbs| |G13|Bi-pin|13 mm pin spacing|Worldwide|T8 and T12 tubes| |G5|Bi-pin|5 mm pin spacing|Worldwide|T5 tubes| |GX53|Recessed disc with pins|53 mm pin spacing|Mains voltage|Low-profile downlights| |R7s|Double-ended|78 or 118 mm long|Mains voltage|Floodlights, uplighters| ## Choosing by lumens, not watts Choose by lumens, not watts. A 40 W incandescent equals about 450 lumens, 60 W about 800, 75 W about 1,100 and 100 W about 1,600. LED versions use roughly 5, 8–9, 11 and 14–16 watts. For reflector lamps, compare center-beam candlepower and beam angle as well. ## Reflector lamps and beam angles BR lamps have a soft-edged wide beam for general downlighting, PAR lamps a tighter, more controlled beam for accent and outdoor flood lighting, and MR16 and GU10 lamps a compact spot for display. Packaging codes such as SP, NFL, FL and WFL indicate spot, narrow flood, flood and wide flood. ## LED tubes: Type A, B, C and A/B LED tubes replace fluorescent T8 and T5 lamps in four ways. Type A plugs into the existing ballast, Type B bypasses the ballast and runs on mains wired to the sockets, Type C uses a separate external driver, and hybrid Type A/B works either way. Type B avoids ballast losses but requires rewiring. ## What to check before you buy Before buying, check four things: the base, whether the lamp physically fits the fixture, enclosed-fixture and damp or wet ratings, and dimmer compatibility. Enclosed glass shades trap heat that shortens LED life, so use lamps rated for enclosed fixtures, and on dimmers choose lamps marked dimmable from the maker's compatibility list. Detailed pages: [E26 vs E27 bulb bases](https://ledlights.org/guides/e26-vs-e27-bulb-base/) · [E12 vs E14 candelabra bases](https://ledlights.org/guides/e12-vs-e14-candelabra-base/) · [B22 bayonet vs E27 screw bases](https://ledlights.org/guides/b22-bayonet-vs-e27/) · [GU10 vs MR16 (GU5.3) spotlight bulbs](https://ledlights.org/guides/gu10-vs-mr16-gu5-3/) · [G9 LED bulbs](https://ledlights.org/guides/g9-led-bulb/) · [GU24 bulbs and sockets](https://ledlights.org/guides/gu24-base/) · [H11 vs 9005 vs 9006 bulbs](https://ledlights.org/guides/h11-vs-9005-vs-9006/) · [H4 vs H7 headlight bulbs](https://ledlights.org/guides/h4-vs-h7-headlight-bulb/) · [1156 vs 1157 bulbs](https://ledlights.org/guides/1156-vs-1157-bulb/) · [3157 vs 7443 bulbs](https://ledlights.org/guides/3157-vs-7443-bulb/) · [194 vs 168 (T10) bulbs](https://ledlights.org/guides/194-vs-168-t10-bulb/) · [CANbus LED bulbs and hyperflash](https://ledlights.org/guides/canbus-led-bulbs-hyperflash/) --- # Outdoor LED lighting URL: https://ledlights.org/guides/outdoor-led-lighting/ · Updated: 2026-11-15 **Definition (Wet-rated light):** A wet-rated light, marked "Suitable for Wet Locations", is built and tested for direct exposure to rain, snow and sprinklers; a damp-rated light only for moisture under cover, such as a roofed porch. Outside North America the same protection is stated as an IP code, such as IP44 or IP65. ## Wet, damp and IP ratings outdoors Any light exposed to rain, snow or sprinklers must be rated for wet locations; under a roofed porch, damp-rated is enough. These are UL and CSA listings in North America, and UL's wet rating assumes mounting at least 4 feet up. Elsewhere, IP codes do the job: IP44 resists splashing, IP65 water jets, IP67 temporary immersion. ## Choosing lights for each part of the yard Match the light to the job. Entrances need a shielded wall light on a dusk sensor; paths need low lights that shine down; driveways and side yards suit motion-switched floodlights; and gardens suit low-voltage path and spot lights. Whatever the job, choose warm white, shield the source from view, and light only what needs to be seen. Table: Outdoor lighting by location |Where|Typical light|Rating|Control| |---|---|---|---| |Entrance, porch|Shielded wall or ceiling light|Damp under a roof, wet if exposed|Photocell or astronomical timer| |Paths, steps|Low path, step or bollard lights|Wet, rated for mounting near the ground|Timer or photocell on the transformer| |Driveway, side yard|Floodlight or wall pack aimed down|Wet|Motion sensor with a built-in light sensor| |Garden, trees, walls|12 V spot and wash lights|Wet, landscape-listed|Timer or photocell on the transformer| |Pool, pond, fountain|Underwater or in-ground lights|Listed for the use, IP68|Timer| |No wiring nearby|Solar stake, string and wall lights|Wet or IP44–IP65|Built-in dark sensor| ## Photocells, timers and motion sensors Three controls switch outdoor lights automatically. A photocell turns them on at dusk, at about 1.5 footcandles (16 lux) for a standard streetlight control, and off at dawn. An astronomical timer calculates sunset from the date and location. A motion sensor turns a light on only when a warm body moves through its view. ## When solar lights work, and when they don't A solar light can only spend what its panel collected that day. In June that is plenty almost everywhere, but a London garden gets about one-seventeenth as much sunlight per hour of darkness in December as in June, Seattle about one-thirteenth and Phoenix about a quarter. Solar suits marker and accent lights; wired lights suit security and steps. ## 12 V low-voltage landscape lighting Low-voltage landscape lighting runs path and spot lights at about 12 V from a transformer plugged into an outdoor outlet. In the US, UL 1838 limits these systems to 15 V and 25 A per circuit, so cable can be buried just 6 inches deep. Size the transformer by volt-amperes and the cable by load and length. ## Dark-sky friendly outdoor lighting DarkSky International and the Illuminating Engineering Society set five principles: light should be useful, targeted, no brighter than needed, controlled by timers or sensors, and warm in color. In practice that means fully shielded fixtures that send no light above the horizontal, 3000 K or warmer, and lights that switch off or dim when not needed. Detailed pages: [Dusk-to-dawn photocells](https://ledlights.org/guides/dusk-to-dawn-photocell/) · [Motion-sensor lights: PIR vs microwave](https://ledlights.org/guides/motion-sensor-lights/) · [Solar garden lights](https://ledlights.org/guides/solar-garden-lights/) · [Landscape lighting transformer sizing](https://ledlights.org/guides/landscape-lighting-transformer-sizing/) --- # LED off-road lights URL: https://ledlights.org/guides/led-off-road-lights/ · Updated: 2026-11-15 **Definition (Off-road LED light):** An off-road LED light is an auxiliary lamp for trucks, Jeeps, UTVs and similar vehicles: a light bar, cube or pod, ditch light, fog replacement, rock light or rear chase light. Most are brighter and wider than headlights and are legal on public roads only when they meet SAE/DOT fog or driving-lamp rules and your state's mounting and color laws. ## What are the different types of LED off-road lights? Off-road LEDs come as light bars, cube or pod lamps, A-pillar ditch lights, fog-light replacements, underbody rock lights, rear chase or dust lights, and camp or scene floods. Bars throw the most light ahead; pods fill gaps and corners; ditch lights catch the roadside; rock and chase lights light the ground under and behind the vehicle. Table: LED off-road light types and typical mounts |Type|Typical mount|Best for| |---|---|---| |Straight / curved light bar|Bumper, grille, roof, windshield|Primary forward fill on open trails| |Cube / pod|Bumper, A-pillar, hood, fairlead|Aimable fill, corners, modular setups| |Ditch / A-pillar|A-pillar or hood brackets|Roadside berms and washouts| |Fog replacement|Factory fog pocket|Low, wide beam in weather| |Rock light|Underbody, rocker, bumper|Wheel placement while crawling| |Chase / dust|Rear bumper, tire carrier|Being seen in dust by followers| |Camp / scene flood|Roof, side, rear|Work and camp light while parked| ## Spot vs. flood vs. combo beam: which one do you actually need? A spot or pencil beam throws a narrow cone far ahead for open trails and high speed. A flood or scene beam spreads wide and short for camping, winching and tight woods. A combo or driving beam mixes both in one housing and is the usual first choice for a single bumper or roof bar. Table: Spot, flood and combo beam patterns for off-road LEDs |Pattern|Distance|Width|Best use| |---|---|---|---| |Spot / pencil|Long (often 300–800+ m at 1 lux on large bars)|Narrow|Desert, fire roads, spotting obstacles early| |Flood / scene|Short to medium|Wide (often 60–120°+)|Woods, camp, work light, rock crawling near field| |Combo / driving|Medium-long|Medium with a brighter center|Daily trail bar when you can only fit one pattern| ## Amber vs. white off-road lights: which performs better in dust and fog? On clear trails, 5700–6500 K white gives crisp contrast and long throw. In dust, fog, rain and snow, 2700–3200 K amber or selective yellow usually feels easier on the eyes because it cuts blue-rich glare from backscattered particles, not because yellow light magically penetrates farther through the cloud. --- # LED shop lights and high-bays URL: https://ledlights.org/guides/led-shop-and-high-bay-lights/ · Updated: 2026-11-15 **Definition (High-bay light):** A high-bay light is a high-output fixture, usually 100–240 W and 15,000–36,000 lumens, hung from ceilings about 15–40 feet up in warehouses, factories and gyms. A shop light is a lower-output strip, usually 4 or 8 feet long, for garages, basements and workbenches under ceilings of roughly 8–14 feet. ## What LED shop light do you need for a garage: 4 ft or 8 ft? A 4 ft LED shop light gives 4,000–5,500 lumens from 35–50 W, and an 8 ft strip gives 8,000–10,000 lumens from 72–100 W. Pick 4 ft units for easy hanging and linking, 8 ft for long, straight runs with fewer fixtures and fewer power drops. Both suit ceilings of 8–12 feet. Table: 4 ft vs 8 ft LED shop lights for garages |Fixture|Typical output|Typical power|Best for| |---|---|---|---| |4 ft strip|4,000–5,500 lm|35–50 W|Garages, basements, benches, tight joist spacing| |8 ft strip|8,000–10,000 lm|72–100 W|Larger shops, long straight runs, fewer fixtures| |4 ft linear high-bay|14,000–22,000 lm|100–150 W|Ceilings of 12–20 ft, racking aisles| ## UFO vs. linear high-bay: which shape is better? UFO high-bays are round, finned fixtures with a tight, bright beam that suit open floors, high ceilings and hot, dusty places. Linear high-bays are long, flat fixtures with wider, softer light that suit aisles, racking and lower ceilings. Linear fixtures usually glare less; UFOs usually mount higher and cost less. Table: UFO vs linear LED high-bay comparison |Feature|UFO high-bay|Linear high-bay| |---|---|---| |Output|15,000–36,000 lm (100–240 W)|10,000–30,000 lm (80–220 W)| |Distribution|Round, 60–120° optics|Wide rectangular, soft edges| |Glare|Higher, small bright source|Lower, larger lens| |Best ceiling|20–40 ft|12–25 ft| |Best use|Open floors, gyms, hot or dusty plants|Racking aisles, retail, shops, light assembly| ## How do mounting height and lux targets set the fixture size? Taller ceilings need more lumens per fixture and tighter beams, because light spreads and weakens with distance. As a guide, 15–20 ft needs about 15,000 lumens, 20–30 ft about 20,000–30,000, and 30–40 ft about 30,000–36,000 with a narrower optic. Space fixtures about one to 1.5 times the mounting height. Table: LED high-bay mounting height, output and optic guide |Mounting height|Typical lumens per fixture|Common optic|Spacing| |---|---|---|---| |12–15 ft|10,000–15,000 lm|Linear or 120° UFO|10–20 ft| |15–20 ft|15,000–22,000 lm|90–120° UFO or linear|15–25 ft| |20–30 ft|20,000–30,000 lm|90° UFO|20–35 ft| |30–40 ft|30,000–36,000 lm|60° UFO|30–45 ft| Note: Rule-of-thumb starting points. Confirm with the manufacturer's photometric file or a layout from the supplier. ### What lux targets suit a garage, shop or warehouse? Typical maintained targets are 100–300 lux for garages and warehouse aisles, 200–300 lux for active picking and packing, 300–500 lux for general assembly and workshops, and 500–1,000 lux for fine bench work. One foot-candle is about 10.76 lux. Design 25–40% higher at installation to allow for dirt and lumen loss. ## Which Type A, B or C LED T8 tube fits an old shop light? Type A tubes run on the existing fluorescent ballast and are the simplest swap. Type B tubes need the ballast removed and mains wired to the sockets. Type C tubes run from a separate low-voltage driver. Choose Type A for speed, Type B for lowest long-term cost, and Type C for dimming and the best efficiency. Table: LED T8 tube types A, B, C and hybrid compared |Type|Power source|Rewiring|Trade-off| |---|---|---|---| |A (plug and play)|Existing electronic ballast|None|Ballast loss and failure risk remain| |B (ballast bypass)|Mains to the sockets|Yes, remove the ballast|Lowest running cost; needs correct wiring and a label| |C (remote driver)|External LED driver|Yes, new driver and wiring|Best dimming; highest installed cost| |A/B (hybrid)|Ballast or mains|Optional|Flexible; check which mode the maker lists| ### How do you bypass a ballast safely, and what is single- vs. double-ended? Turn off the breaker, lock it out, and confirm the circuit is dead with a tester before touching wires. Single-ended tubes take line and neutral at one socket end; double-ended tubes take line at one end and neutral at the other. Wire to the tube's diagram, use non-shunted sockets, and label the fixture. ## When should you use a high-bay instead of a shop strip? Use shop strips and wraps under ceilings of about 8–12 feet. From 12 to 15 feet, a linear high-bay or low-bay fixture is the middle ground. Above about 15 feet, use UFO or linear high-bays, because strips cannot deliver enough light at that distance without close spacing, glare or too many fixtures. Table: Choosing between LED shop strips and high-bays by ceiling height |Ceiling height|Best fixture|Typical space| |---|---|---| |8–12 ft|4 ft or 8 ft shop strip, T8 LED tubes|Garage, basement, small shop| |12–15 ft|Linear high-bay, low-bay, or wide-beam UFO|Large garage, retail back room, small plant| |15–25 ft|Linear high-bay or 90–120° UFO|Warehouse aisles, gym, workshop| |25–40 ft|UFO high-bay, 60–90° optic|Distribution center, hangar, factory floor| --- # LED grow lights URL: https://ledlights.org/guides/led-grow-lights/ · Updated: 2026-11-15 **Definition (Daily light integral (DLI)):** The daily light integral (DLI) is the total number of photosynthetically active photons that land on one square meter of plants in a day, in moles per square meter per day. It is the plant equivalent of a daily dose, and it is calculated as PPFD × hours of light × 0.0036. ## PAR, PPF and PPFD: measuring light for plants Plants respond to photons, not lumens. PAR is the 400–700 nm band they use. PPF, in µmol/s, is a fixture's total PAR output; PPFD, in µmol/m²/s, is what lands on one square meter of canopy. PPF describes the lamp, PPFD describes a place, and the same fixture gives very different PPFD at different heights. ## Daily light integral (DLI): the formula DLI is the total PAR photons a canopy receives in a day, in mol/m²/day. Calculate it as PPFD × hours of light × 0.0036, because 3,600 seconds per hour divided by 1,000,000 converts micromoles to moles. For example, 250 µmol/m²/s for 16 hours gives 14.4 mol/m²/day, a typical lettuce target. ### Typical DLI targets: lettuce, herbs and cannabis Conservative published and extension targets are about 12–17 mol/m²/day for lettuce and leafy greens, 15–25 for basil and other herbs, about 20–40 for vegetative cannabis and 30–45 or more in flower. Treat them as starting points: cultivar, CO₂, temperature, nutrition and growth stage all move the optimum for your crop. Table: DLI targets by crop with an example PPFD and photoperiod |Crop / stage|DLI (mol/m²/day)|Example that delivers it| |---|---|---| |Seedlings, clones, microgreens|6–15|175 µmol/m²/s × 16 h ≈ 10| |Lettuce and leafy greens|12–17|250 µmol/m²/s × 16 h ≈ 14| |Herbs (basil)|15–25|350 µmol/m²/s × 16 h ≈ 20| |Tomatoes, peppers, cucumbers|20–30|500 µmol/m²/s × 14 h ≈ 25| |Cannabis, vegetative|20–40|430 µmol/m²/s × 18 h ≈ 28| |Cannabis, flowering|30–45+|830 µmol/m²/s × 12 h ≈ 36| Note: Starting targets; actual needs vary. The last column is one example schedule that delivers a mid-range dose. --- # LED Christmas lights URL: https://ledlights.org/guides/led-christmas-lights/ · Updated: 2026-11-15 **Definition (LED Christmas lights):** LED Christmas lights are seasonal light strings that use light-emitting diodes instead of tiny incandescent filament bulbs. They sit on a standard plug and cord, are tested under UL 588 in North America, and use a fraction of the power, give off little heat and last for many seasons. ## Are LED Christmas lights better than incandescent ones? Mostly yes. LED strings use roughly 85–90% less power, stay cool to the touch, and are rated for 20,000 hours or more against 1,000–3,000 for incandescent. Incandescent sets win only on the exact amber glow of a heated filament, and on price for the cheapest sets. Table: LED vs incandescent Christmas lights |Feature|Incandescent|LED| |---|---|---| |100 mini lights|About 40 W|About 4–6 W| |25 C9 bulbs|About 175 W (7 W each)|Well under 25 W| |Heat|Bulbs get hot, C7 and C9 especially|Barely warm| |Rated life|Commonly 1,000–3,000 h|Commonly 20,000 h or more| |Usual failure|Burnt filament, loose bulb|Driver, wire, socket or moisture| |Glow|Soft, warm, slightly uneven|Bright point sources, vivid colors| |Sets per outlet|A few; read the label|Many more; read the label| ## What are C7, C9 and mini Christmas lights? C7 and C9 are the large bulbs, named by width in eighths of an inch: a C7 is 7/8 inch across on an E12 candelabra base, and a C9 is 1⅛ inch on an E17 intermediate base. Mini lights are the small bulbs on thin wire. Icicle, net and curtain sets are minis arranged in shapes. Table: Christmas light types and typical sockets |Type|Size and base|Typical use| |---|---|---| |Mini|Small bulb or 5 mm LED, in a push-in socket|Trees, wreaths, garland, shrubs| |C7|7/8 inch bulb, E12 base, up to 5 W incandescent|Rooflines, smaller trees| |C9|1⅛ inch bulb, E17 base, up to 7 W incandescent|Rooflines, large trees, eaves| |Globe|Round bulbs on candelabra or mini sockets|Patios, porches, wide trees| |Icicle, net, curtain|Minis on pre-arranged wire|Eaves, shrubs, windows| |Rope, fairy|LEDs in a tube or on thin copper wire|Railings, mantels, jars| ## Which LED Christmas lights look like old incandescent ones? Look for a stated color temperature of 2200–2700 K, often sold as warm white, extra warm or candlelight. Incandescent Christmas bulbs glow at roughly 2400–2700 K. Anything sold as cool white, or 5000 K and up, looks blue-white beside them. Colored LEDs are more saturated than the coated glass of old bulbs. ## What rating do outdoor Christmas lights need? Use only sets marked for outdoor use. In North America that means a UL, ETL or CSA listing to UL 588 with the red UL label, and in Europe an IP44 or higher rating. Indoor-only sets, with the green label, are not built for rain. Keep plugs off the ground and use a GFCI outlet. Table: Markings on Christmas lights and outdoor cords |Marking|Meaning| |---|---| |Red UL label|Set is listed for indoor and outdoor use| |Green UL label|Set is listed for indoor use only| |ETL or CSA mark|Tested to the same standard by another recognized lab| |IP44|Splash-proof; usual minimum for outdoor sets in Europe| |IP65|Protected against water jets; commercial or low-voltage sets| |"W" on a cord|Extension cord suitable for outdoor use| ### What does "full-wave rectified" mean on LED light sets? An LED conducts in one direction only, and household current reverses 60 times a second. A half-wave set lights its LEDs for half of every cycle, so they pulse at 60 Hz, which some people see as flicker and cameras record as banding. A full-wave rectified set uses the whole cycle and pulses at 120 Hz. ## What makes Christmas lights safe to use? Buy sets listed by UL, ETL or CSA, a mark showing they were tested to UL 588. Use them only where the label allows, do not exceed the stated number of connected strings, replace fuses with the same rating, and discard sets with cracked sockets or damaged wire. Switch them off when you leave or sleep. --- # LED headlights and conversions URL: https://ledlights.org/guides/led-headlights/ · Updated: 2026-11-15 **Definition (LED headlight):** An LED headlight is a vehicle headlamp whose light comes from light-emitting diodes instead of a halogen filament or an HID arc. It is legal and predictable when the whole lamp was designed and certified around its LEDs. It is a gamble when an LED bulb is pushed into a housing designed for a halogen filament. ## How do factory LED headlights differ from halogen ones? A factory LED headlamp is designed around its LEDs: chips, lenses or reflectors, heat sink and driver are tested together as one certified unit. A halogen headlamp is designed around a glowing filament in a replaceable bulb. That difference in design, more than raw lumens, explains why LED conversions behave so differently. ### What are the common problems with halogen reflector headlights? Most dim halogen headlights are limited by the lens and reflector, not the bulb. Yellowed or hazed polycarbonate can cut light output sharply, an old reflector coating loses shine, and a corroded socket or thin wiring drops voltage. Restoring the lens, fixing the connector and re-aiming often helps more than any bulb swap. ## Why do some LED bulbs cause glare and dark spots? A headlamp housing focuses light from a filament's exact position. An LED bulb emits from flat chips facing outward, so even a small offset sends light above the cutoff into oncoming eyes while leaving dark patches on the road. Good bulbs copy the filament's position and size, and the lamps must be aimed again. ### What is a cutoff, and how do you check it? The cutoff is the sharp upper edge of a low beam that keeps light off the eyes of oncoming drivers. In right-hand traffic it is flat on the left and steps up toward the right shoulder. Park square to a wall at night and check that the edge is crisp, with no bright light above it. ### Which LED bulb designs come closest to a filament? The closest designs use thin double-sided or slim-board emitters, with chips placed where the filament sat. Compact CSP chips help, and a rotatable collar lets you aim the chips sideways, usually at 3 and 9 o'clock. Check that the chips are the same size as the halogen filament and that the board does not block the shield. ## HID vs LED vs halogen: how do they compare? Halogen is cheap, instant, warm in color and short-lived at about 1,000 lumens per low beam. HID xenon puts out roughly three times that from a 35 W arc but needs a ballast, warm-up and projector optics. LED matches or beats HID with less power, instant start, and life measured in the tens of thousands of hours. Table: HID, LED and halogen headlights compared |Feature|Halogen|HID (xenon)|LED| |---|---|---|---| |Light source|Heated tungsten filament in halogen gas|Arc between electrodes in xenon and metal salts|Semiconductor chips with phosphor| |Rated output per bulb|About 1,000–1,700 lm (H7 about 1,500)|About 3,200 lm (D2S, 35 W)|Varies: good lamps 1,000–3,000+ lm in the beam| |Power per lamp|55–65 W|35 W plus ballast losses|15–40 W| |Typical color|About 3,000–3,200 K|About 4,100–4,500 K|5,000–6,500 K| |Start-up|Instant|A few seconds to strike and settle|Instant| |Rated life|500–1,000 h|2,000–3,000 h|10,000–50,000 h, with good cooling| |Needs special optics|No, works in reflectors|Projector, plus auto-leveling and washers above 2,000 lm in ECE countries|Designed in; retrofit bulbs fit best in projectors| |Plug-in retrofit in the U.S.|Standard|Not permitted|Not permitted| Note: Typical figures for a low beam. Halogen and HID follow ECE regulations; LED depends heavily on design and cooling. ## Projector or reflector: which housing handles LED bulbs better? A projector headlight focuses light through a lens and a metal cutoff shield, giving a sharp edge that tolerates small source changes. A reflector headlight bounces light off a shaped bowl and depends on the source sitting exactly where the filament was. For LED bulbs, projectors are more forgiving, but both can fail. Table: Projector and reflector headlight housings compared for LED retrofit |Housing|How it forms the beam|Cutoff|With an LED bulb| |---|---|---|---| |Reflector|Light from the filament reflects off a faceted or smooth bowl behind it|Made by the filament shield or the reflector shape; soft|Most sensitive: chip position errors scatter light above the cutoff and leave dark patches| |Projector|Reflector focuses light through a lens, and a shield blocks the top|Sharp and adjustable by shield design|More forgiving, but the chips must sit at the focus; some bulbs still bloom above the line| |Factory LED module|Chips, lens or reflector and shield are designed together|Sharp, certified|Not applicable: the lamp is the LED| ## Are plug-in LED headlight bulbs legal? In the United States, no: NHTSA says FMVSS 108 permits only the replaceable bulbs filed under 49 CFR Part 564, and no LED bulb is filed. In UNECE countries, only approved LED substitutes are legal, in listed vehicles. A complete DOT-compliant LED headlamp assembly is the clear legal route. ### What does FMVSS 108 say about LED bulbs in halogen housings? FMVSS 108 requires headlamp bulbs to match the specifications filed in 49 CFR Part 564, and NHTSA has said no LED bulb is filed, so none is permitted in a replaceable-bulb headlamp. The federal rule applies to what is sold, and "for off-road use only" labels do not make an on-road conversion lawful. ### What about Europe and other countries? UNECE countries allow LED substitutes only when they hold approval under UN Regulation 128 or a national certificate, and only in vehicles on the maker's list. Germany's KBA has approved a handful of LED H7 and H4 bulbs, and UN R128 added H11/LED. Most other LED bulbs sold online lack any approval. ### What is the legal way to upgrade to LED headlights? Fit a complete LED headlamp assembly, ideally DOT or SAE marked in the U.S. or E-marked in Europe, and aim it after installation. Some cars have factory LED housings you can swap for, and many round sealed-beam sizes have complete LED replacements. Replacing a hazed lens or a worn halogen with a quality bulb is legal too. ## Do LED headlight bulbs need fans or heat sinks? Yes. A headlight LED dissipates 15–30 W of heat in a very small space, and chips lose light and life as they heat up. Cooling is done by an aluminum heat sink, flexible braided copper straps or a small fan. All three work, but each needs room behind the lamp and a dust cap that still fits. ### What should you check before buying: clearance, dust cap and driver? Measure the free space behind the headlamp, because most LED bulbs are much longer than the halogen they replace. Check that the dust cap can still seal, that the driver box has a place to sit, and that the connector, harness and bulb-out sensing suit your car. ## What color temperature should LED headlights be? Choose 5500–6500 K white, which looks like daylight and gives good contrast. Halogen is about 3000–3200 K and OEM HID about 4100–4500 K. Blue-tinted 8000 K bulbs cut usable light, glare more in rain and snow, and may fail the white-color limits headlamps must meet. --- # LED strip lighting URL: https://ledlights.org/guides/led-strip-lighting/ · Updated: 2026-11-15 **Definition (LED strip light):** An LED strip light is a flexible printed circuit with LEDs mounted at regular intervals, usually powered from a low-voltage constant-voltage supply and sold on reels of 5 m. It gives a long, thin line of light for coves, cabinets, shelves, vehicles and signs, and it can be cut to length at marked points. ## COB or SMD strip: which should you buy? Buy SMD strips for the best price, efficacy and range of colors when the strip will be hidden or diffused. Buy COB strips when the strip is visible or reflected, because hundreds of tiny dies per metre give a continuous line of light with no dots. COB costs more, runs warmer and offers fewer color options. Table: COB and SMD LED strips compared for buyers |Feature|SMD strip (2835)|COB strip (dotless)| |---|---|---| |Look|Visible dots unless diffused|Continuous line, no dots| |Density|60–240 LEDs/m|320–528 dies/m| |Power per metre|6–20 W|8–15 W| |Light per metre|600–2,200 lm|800–1,500 lm| |Color choice|Wide: CCT, RGB, RGBW, tunable, high CRI|Mostly white, tunable white and RGB are growing| |Best for|Coves, cabinets and channels with diffusers|Open or glossy installs, glass shelves, signage| |Price|Lower|Higher| Note: Typical values; always check the maker's lumens per metre, CRI and wattage data. ## 12 V or 24 V: which LED strip should you buy? Buy 24 V for fixed installations: at the same power it draws half the current of 12 V, so it loses less voltage, runs farther from one feed and needs thinner wire. Buy 12 V for cars, boats, RVs and battery systems, and 5 V only for short addressable strips or USB-powered projects. ## How many LEDs and lumens per metre do you need? Judge brightness by lumens per metre, not LED count or color claims. White strips usually make 300–600 lm/m for accents, 800–1,200 for cove and under-cabinet light, and 1,500 or more for task or high-output work. Higher density, 120–240 LEDs per metre, also hides dots and lets each chip run cooler. Table: Typical LED strip brightness and density by use |Use|Lumens per metre|Watts per metre|LEDs per metre| |---|---|---|---| |Accent, TV bias, backlight|200–500|3–6|60–120| |Cove, shelf and toe-kick|500–1,000|6–10|120–240| |Under-cabinet task light|800–1,200|8–12|120–240| |Workshop, garage, task|1,200–2,000+|12–20|240+ or COB| Note: Rules of thumb for white strips at about 100 lm/W. Real needs depend on the surface, distance and diffuser. ## What CRI and color temperature should a strip have? Choose CRI 90+ with a high R9 for homes, kitchens and anything with skin, wood or food. CRI 80 is fine for accent and garage use. Pick 2700–3000 K for living spaces and 3000–4000 K for kitchens and workshops, and buy a whole project from one batch, because separate reels can differ in color. ## How do you cut and join LED strips? Cut only along the marked line through the copper pads, usually every three LEDs on 12 V strips and six on 24 V strips. Rejoin sections with soldered wire and heat-shrink for a permanent joint, or with solderless clips for quick indoor work. Check polarity, seal cut ends on coated strips, and avoid sharp bends at the joint. ### How do you solder an LED strip? Tin each copper pad with a little solder, tin the wire end, then touch the two together with a temperature-controlled iron for about two seconds. Use stranded wire sized for the current, add heat-shrink to the joint, and test before you stick the strip down. Too much heat lifts the pad, so work quickly. ### Are solderless strip connectors reliable? Clip connectors are fine for indoor, low-current, easy-access joints. They clamp spring contacts onto the pads, so a poor fit, an uneven strip or vibration can give flicker or a dead section. For high-power, outdoor or hidden joints, solder, or use sealed waterproof connectors, and match the connector's width and number of pins to the strip. ## How do you avoid voltage drop on long runs? Voltage drop dims the far end of a strip because current flows through thin copper. Stay within the maker's maximum run per feed, often one 5 m reel at 12 V, prefer 24 V, and feed long runs from both ends or every few metres. Use wire thick enough from the supply, and let the calculator check your numbers. ## Do LED strips need aluminum channels and diffusers? Yes, for anything left on for long hours. An aluminum channel carries heat away, keeps the strip straight and protects it, while an opal diffuser turns separate dots into a smooth line. Choose a channel that fits the strip's width, usually 8 or 10 mm, and one deep enough, about 10–15 mm, to hide the dots. Table: Aluminum channel types for LED strips and their uses |Channel|Mount|Best for| |---|---|---| |Surface|Screws or tape on a flat face|Under cabinets, shelves, general use| |Recessed (flush)|Routed groove in wood or panel|Furniture, stair edges, clean architectural lines| |Corner (45°)|Inside corner of two surfaces|Coves, cabinets and ceilings, wall washing| |Plaster-in or drywall|Set into plaster or drywall|Cove lighting and continuous ceiling lines| |Bendable|Flexible aluminum or plastic|Curves and arches| ## How do you light under cabinets with LED strips? Mount the strip near the front edge of the cabinet underside, behind a lip or in a channel, so it lights the counter without glare or reflections on glossy surfaces. Use 24 V, 3000–4000 K and CRI 90+, aim for 800–1,200 lumens per metre, and put the power supply and dimmer where they stay accessible. --- # LED street and parking lot lights URL: https://ledlights.org/guides/led-street-and-parking-lights/ · Updated: 2026-11-15 **Definition (Cobra-head):** A cobra-head is the standard roadway luminaire: a slim, curved housing on a mast arm, named for its hooded shape. It was built for high-pressure sodium (HPS) lamps and is now almost always LED. It lights the road from the side, and a cutoff optic keeps most light out of the sky and windows. ## What are the main types of LED street and parking lights? Four fixture families cover most outdoor public lighting. Cobra-heads on mast arms light roads, shoebox area lights on poles light parking lots, wall packs light building edges and doors, and floodlights light wide targets such as signs, yards and sports areas. Each is built around a different beam pattern. Table: LED street and parking light types, mounting and use |Type|Typical mounting|Typical LED power|Best for| |---|---|---|---| |Cobra-head|25–40 ft pole arm|40–200 W|Residential and arterial streets| |Shoebox / area light|20–40 ft pole|75–300 W|Parking lots, plazas, car lots| |Wall pack|8–20 ft on a wall|15–120 W|Doors, docks, building perimeter| |Floodlight|Yoke, bracket or pole|10–400 W|Signs, facades, yards, sports| ## How do beam types and BUG ratings work? The IES classifies outdoor beam shapes by number. Type II is a long narrow strip for roads, Type III a wider forward throw for pole edges, Type IV a half circle for walls, and Type V a round pattern for pole centers. The BUG rating scores backlight, uplight and glare, so lower is better. ## What color and shielding do dark-sky and AMA guidance call for? The American Medical Association has advised since 2016 that community LEDs be 3000 K or lower, with the lowest practical glare and dimming late at night. Dark-sky guidance adds full cutoff shielding, no uplight and lights that are on only when needed. Near turtle beaches and observatories, use amber, around 590 nm. ## How do photocells and controls switch these lights? A photocell turns the light on at dusk, usually near 1.5 footcandles (16 lux), and off at dawn. Most streetlights and many area lights use a twist-lock photocell in a standard receptacle, which fails closed so the light stays on. Newer sockets add a 7-pin connection for dimming and remote control. ## How much more efficient are LEDs than HPS streetlights? An LED roadway fixture typically delivers 100–150 lm/W at the fixture, against roughly 60–80 lm/W for an HPS cobra-head once ballast and optical losses are counted. Replacing 250 W HPS heads with 100–130 W LEDs cuts energy use by 50–70%, and the light is whiter, with CRI above 70 against about 20. --- # Marine LED lights URL: https://ledlights.org/guides/marine-led-lights/ · Updated: 2026-11-15 **Definition (Navigation lights):** Navigation lights are the colored lights a vessel must show between sunset and sunrise so others can tell its heading and type. Their colors, arcs and minimum visible ranges are fixed by the international collision regulations (COLREGs). LED versions must still match those arcs and colors, not just be bright. ## What arcs and colors do navigation lights show? A powered vessel under way shows a white masthead light over a 225° arc ahead, a red port and a green starboard sidelight each covering 112.5°, and a white sternlight over 135°. Together they cover a full circle. At anchor a vessel shows an all-round white light instead. Table: Navigation light arcs, colors and minimum visibility by vessel length (COLREGs Rules 21 and 22) |Light|Color|Arc|12–50 m vessel|Under 12 m| |---|---|---|---|---| |Masthead|White|225°|5 nm (3 nm under 20 m)|2 nm| |Sidelights|Red (port), green (starboard)|112.5° each|2 nm|1 nm| |Sternlight|White|135°|2 nm|2 nm| |All-round (anchor)|White|360°|2 nm|2 nm| ## How waterproof and corrosion-resistant should marine LEDs be? Choose IP67 as the minimum for deck, mast and cabin-exterior lights, and IP68 for lights that sit below the waterline or are often submerged. Waterproofing is only half the job: salt corrodes metal, so look for 316 stainless or anodized housings, potted electronics and tinned copper wire. ## Do marine LEDs run on 12 V or 24 V, and how much current do they use? Most boats have a 12 V DC system, and larger or commercial vessels use 24 V. Quality marine LEDs include a constant-current driver that accepts about 9–32 V, so one light suits both. A typical LED navigation light draws roughly 0.1–0.5 A, against 1–2 A for the incandescent bulb it replaces. ## What are underwater, dock and courtesy lights for? Underwater lights, usually fitted to the transom or the drain plug, light the water for swimming, fishing and appearance, and blue or green penetrates farthest. Dock lights are low-voltage lights for safe footing. Courtesy and cabin lights use red to protect night vision, and deck floods light work areas. --- # LED flashlights URL: https://ledlights.org/guides/led-flashlights/ · Updated: 2026-11-15 **Definition (Beam distance):** Beam distance is how far a flashlight lights a target to 0.25 lux, about the light of a full moon, as defined by the ANSI FL1 standard. It depends on candela, the light's peak intensity, and not on lumens: it equals twice the square root of the candela, so 10,000 cd reaches about 200 m. ## What is the difference between lumens and candela? Lumens measure all the light a flashlight emits, in every direction. Candela measures how intense the brightest part of the beam is. Throw, the distance at which the beam is still useful, depends on candela, so a narrow beam with fewer lumens can reach far beyond a wide beam with more. Table: Example flashlights: lumens, candela and FL1 beam distance |Light type|Lumens|Peak candela|Beam distance| |---|---|---|---| |Camp lantern (omnidirectional)|300|~24|~10 m| |Flood-style everyday light|1,000|3,000|~110 m| |Thrower (similar lumens)|1,200|100,000|~630 m| |Searchlight|5,000|1,000,000|2,000 m| ## How do flood and throw beams differ, and which do you need? A flood beam spreads light wide and soft for close work, camping and walking. A throw beam concentrates it into a tight hotspot for distance. Throw comes from a large reflector or lens in front of a small emitter, so a flashlight with a long thin head throws and one with a short wide head floods. ## Which battery type is best: alkaline, NiMH or 18650 Li-ion? Alkaline cells are cheap and long-lasting on a shelf but sag and leak under high drain. NiMH AA cells give 1.2 V, recharge hundreds of times and hold charge when idle. A rechargeable 18650 lithium-ion cell stores two to three times as much energy and delivers high current, but needs a good charger. Table: Flashlight battery chemistries compared |Cell|Nominal voltage|Typical capacity|Best for|Watch out for| |---|---|---|---|---| |Alkaline AA|1.5 V|2,000–3,000 mAh (low drain)|Emergency kits, low-power lights|Voltage sag at high drain, leaks when depleted| |NiMH AA (low self-discharge)|1.2 V|1,900–2,800 mAh|Everyday lights, 500–2,000 recharges|Slightly lower voltage, so a little less peak output| |Lithium primary AA / CR123A|1.5 V / 3 V|~3,000 / ~1,500 mAh|Cold weather and long storage (shelf life of 10 years or more)|Not rechargeable, higher price| |Li-ion 18650|3.6–3.7 V (4.2 V full)|2,500–3,600 mAh|High-output lights|Needs a proper charger, protection, quality cells| |Li-ion 21700|3.6–3.7 V (4.2 V full)|4,000–5,000 mAh|Larger lights, long runtime|Larger and heavier than 18650| ## What do the ANSI FL1 ratings on the box mean? ANSI FL1 is a standard that defines how makers must measure and label a flashlight. It covers light output in lumens measured 30 seconds after switching on, runtime until output falls to 10%, peak beam intensity in candela, beam distance, drop resistance and water resistance rated IPX4, IPX7 or IPX8. ## How do you estimate a flashlight's runtime? Multiply battery voltage by capacity in amp-hours to get watt-hours, take about 90% for driver losses, and divide by the LED's power draw. A 3,000 mAh 18650 holds about 10.8 Wh, so a mode drawing 3 W runs roughly three hours. Heat can force high modes to step down early. ## Can a flashlight really make 100,000 lumens? Rarely, and never from a pocket light. Light output cannot exceed power times efficacy, and a battery and a heat sink limit both. At 100–130 lumens per watt, one 18650 cell cannot honestly produce more than a few thousand lumens, so claims in the tens of thousands or millions are inflated. --- # UV-C LED disinfection URL: https://ledlights.org/guides/uv-c-led-disinfection/ · Updated: 2026-11-15 **Definition (Germicidal UV):** Germicidal ultraviolet (GUV) is ultraviolet radiation, mainly UV-C between 200 and 280 nm, used to inactivate bacteria, viruses and other microorganisms by damaging their DNA and RNA. Low-pressure mercury lamps emit it at 253.7 nm; UV-C LEDs emit a single chosen wavelength, usually between 255 and 280 nm. ## How does UV-C light disinfect? UV-C is absorbed by the DNA and RNA of bacteria, viruses and protozoa, and the damage stops them replicating, so they can no longer cause infection. Nucleic acids absorb most strongly near 260 nm, and the standard germicidal response curve peaks at about 265 nm, which is why UV-C LEDs are made for 255–280 nm. ## What UV dose does disinfection need? UV dose is irradiance multiplied by time, in millijoules per square centimeter: 1 mW/cm² for 40 seconds delivers 40 mJ/cm². NSF/ANSI 55 requires 40 mJ/cm² for Class A water purifiers and 16 for Class B, and the IES cites 20 to 100 mJ/cm² for surfaces. Each added log of reduction removes another 90% of what remains. Table: UV dose required for inactivation credit in drinking water, in mJ/cm² (US EPA, 40 CFR 141.720, for 254 nm low-pressure mercury lamps) |Log reduction|Share inactivated|Cryptosporidium|Giardia|Viruses| |---|---|---|---|---| |1 log|90%|2.5|2.1|58| |2 log|99%|5.8|5.2|100| |3 log|99.9%|12|11|143| |4 log|99.99%|22|22|186| ## UV-C LEDs compared with mercury lamps A low-pressure mercury lamp turns about 30–45% of its input power into UV-C at 253.7 nm. The best commercial UV-C LEDs reach about 10%, and many only a few percent, with milliwatts per chip. LEDs are mercury-free, start instantly, make no ozone and can be built for a chosen wavelength. Table: UV-C LEDs compared with low-pressure mercury germicidal lamps |Property|Low-pressure mercury lamp|UV-C LED| |---|---|---| |Wavelength|253.7 nm, fixed by the mercury discharge|Set by the AlGaN chip, about 255–280 nm; 265 and 275 nm are the most common| |Input power emitted as UV-C|About 30–45%|Near 10% for the best commercial devices around 265 nm; often a few percent| |Form|Glass discharge tube, like a fluorescent lamp|Small chip on a heat-sinked board, used in arrays| |Warm-up|Needs time to reach full output|None| |Mercury|Yes|None| |Ozone|A second line at 184.9 nm makes ozone unless the lamp glass absorbs it|None at 255–280 nm| ## Where UV-C LEDs work: water, air and surfaces UV-C LEDs suit small, enclosed jobs best. In point-of-use water purifiers the light is sealed inside and can switch on only when water flows. Air is treated inside ducts or closed air cleaners. Surfaces are hardest: UV-C does not penetrate dirt or reach shadows, so the IES calls it a supplement to cleaning, not a replacement. ## Is UV-C from LEDs safe for eyes and skin? No. Direct UV-C exposure injures the cornea and skin. The ICNIRP limit for unprotected eyes and skin is 3 mJ/cm² in eight hours at 270 nm, the most hazardous wavelength and close to where UV-C LEDs emit. A source strong enough to disinfect in seconds exceeds that limit in a fraction of the time. Table: ICNIRP 8-hour exposure limits for unprotected eyes and skin at UV-C wavelengths |Wavelength|Typical source|Limit in 8 h (mJ/cm²)|Relative hazard| |---|---|---|---| |220 nm|Near the 222 nm excimer lamp line|25|0.12| |254 nm|Low-pressure mercury lamp|6.0|0.50| |260 nm|UV-C LED|4.6|0.65| |265 nm|UV-C LED|3.7|0.81| |270 nm|UV-C LED|3.0|1.00| |275 nm|UV-C LED|3.1|0.96| |280 nm|UV-C LED|3.4|0.88| Table: Time to deliver a surface-disinfection dose compared with time to reach the ICNIRP eye and skin limit at 270 nm (calculated) |Irradiance at the target|Time to deliver 20 mJ/cm²|Time to deliver 100 mJ/cm²|Time to reach the 3 mJ/cm² limit| |---|---|---|---| |0.1 mW/cm²|3 min 20 s|16 min 40 s|30 s| |1 mW/cm²|20 s|1 min 40 s|3 s| |2 mW/cm²|10 s|50 s|1.5 s| |10 mW/cm²|2 s|10 s|0.3 s| ## Who checks UV-C products and their claims? Often nobody before sale. In the United States, UV lights sold with germicidal claims are pesticide devices: the EPA does not register them or routinely review their safety or efficacy, and an EPA establishment number only identifies the factory. Independent evidence comes from certification to standards such as NSF/ANSI 55, IEC 62471-6 and UL 8802. Table: Standards and rules that apply to UV-C disinfection products |Standard or rule|Applies to|What it covers| |---|---|---| |NSF/ANSI 55|Point-of-use and point-of-entry UV water treatment, 240–300 nm, including LEDs since 2019|Disinfection performance: Class A (40 mJ/cm²) and Class B (16 mJ/cm²), plus labeling and literature| |IEC 62471-6:2022|UV lamp products, including UV LED products|Optical radiation safety assessment, risk groups, user safety information and labeling| |ISO 15858:2016|UV-C devices in ducts, in the upper air of rooms and portable in-room units; not water products|Minimum human safety requirements; adopts 6 mJ/cm² at 254 nm for an 8-hour day| |ANSI/CAN/UL 8802|UV germicidal equipment and systems; not hand-held equipment|Safeguards against UV overexposure, such as mounting height, baffles, sensors and containment| |US EPA, FIFRA|UV lights sold with germicidal claims|Registered establishment, label requirements and truthful claims; no review of safety or efficacy| ## How to judge a UV-C LED product Look for a stated wavelength between about 255 and 280 nm, the irradiance in mW/cm² at a stated distance, and a test report giving the log reduction for a named organism. Prefer enclosed or interlocked designs, check water units for NSF/ANSI 55 certification, and distrust open devices that promise disinfection in seconds. --- # LED calculators and tools URL: https://ledlights.org/tools/ · Updated: 2026-11-15 **Definition:** The series resistor calculator finds the right current-limiting resistor for one LED or a string, picks the nearest standard E24 value, draws its color bands and checks the power rating. The energy savings calculator converts incandescent, halogen or CFL bulbs, or metal-halide, high-pressure sodium and fluorescent fixtures, into equivalent LED lumens and watts and estimates kWh, dollars and CO₂ saved per year, with payback and ROI for commercial retrofits. The LED strip calculator sizes a strip's power supply and feed wire and shows its voltage drop. All three can copy their results, share a link with your values and print a spec sheet. ## LED series resistor calculator The series resistor calculator works out the current-limiting resistor for one LED or a series string from the supply voltage, the LED forward voltage and the current you want. It then picks the nearest standard E24 value, shows its color bands and checks the power rating. ## LED strip power supply and voltage drop calculator The LED strip calculator sizes the power supply for a strip from its voltage, power per metre and length. It also estimates the voltage drop along the strip and in the feed wires, the lowest voltage on the strip, how long a run each feed point can serve and the wire size to use. ## LED lighting-equivalent and energy-savings calculator The energy savings calculator converts incandescent, halogen and CFL bulbs, or metal-halide, high-pressure sodium and fluorescent fixtures, into equivalent LED lumens and watts. From the quantity, hours per day and electricity rate, it estimates annual kWh, cost and CO₂ savings, lamp replacements avoided and, for commercial retrofits, net cost after rebates, simple payback and 5-year return. ## Quick reference Most LEDs run at a forward voltage set by their color: about 1.2–1.6 V for infrared, 1.8–2.2 V for red, 2.0–2.2 V for amber and yellow, and 2.8–3.4 V for green, blue and white at 20 mA. Key formulas include λ ≈ 1240 ÷ Eg and DLI = PPFD × hours × 0.0036. Table: Typical LED forward voltage by color |Color|Wavelength|Material|Typical Vf| |---|---|---|---| |Infrared|850–940 nm|GaAs / AlGaAs|1.2–1.6 V| |Red|620–660 nm|AlInGaP / AlGaAs|1.8–2.2 V| |Orange / amber|590–615 nm|AlInGaP|2.0–2.2 V| |Yellow|585–595 nm|AlInGaP|2.0–2.2 V| |Green (InGaN)|515–530 nm|InGaN|2.8–3.4 V| |Blue|450–475 nm|InGaN|2.8–3.3 V| |White|Blue + phosphor|InGaN + YAG|2.8–3.3 V| |UV-A|365–405 nm|InGaN / GaN|3.0–3.9 V| Note: Typical forward voltage at 20 mA for standard indicator LEDs. High-power LEDs at 350 mA+ run 0.2–0.5 V higher. --- # LED series resistor calculator URL: https://ledlights.org/tools/led-series-resistor-calculator/ · Updated: 2026-11-16 **Definition (Series resistor):** A series resistor is the current-limiting resistor for one LED or a series string. An LED's forward voltage is almost constant over its operating range, so the resistor drops the excess voltage, and Ohm's law gives the resistance that sets the current you want: subtract the total forward voltage of the LEDs from the supply voltage and divide by the desired current, R = (Vs − n × Vf) ÷ If. ## Series resistor calculator To choose an LED resistor, subtract the total forward voltage of the LEDs from the supply voltage and divide by the desired current: R = (Vs − n × Vf) ÷ If. This calculator does that, rounds up to the nearest standard E24 value, shows the color bands and checks the power rating. ## How the calculation works The resistor drops the excess voltage, so Ohm's law gives the value: a 3.0 V white LED at 20 mA on a 5 V supply needs (5 − 3.0) ÷ 0.020 = 100 Ω. The calculator rounds up to the next E24 value, recomputes the current and recommends a power rating twice the dissipation. ## Practical tips Use one resistor per LED or per series string, never one shared resistor for parallel LEDs, because one LED will hog the current. Series strings waste less power, the longer anode lead goes to positive, and above about 350 mA a constant-current driver works better than any resistor. ## Typical forward voltage by color Most LEDs run at a forward voltage set by their color: about 1.2–1.6 V for infrared, 1.8–2.2 V for red, 2.0–2.2 V for amber and yellow, and 2.8–3.4 V for green, blue and white at 20 mA. High-power LEDs at 350 mA and above run 0.2–0.5 V higher. Table: Typical LED forward voltage by color |Color|Wavelength|Material|Typical Vf| |---|---|---|---| |Infrared|850–940 nm|GaAs / AlGaAs|1.2–1.6 V| |Red|620–660 nm|AlInGaP / AlGaAs|1.8–2.2 V| |Orange / amber|590–615 nm|AlInGaP|2.0–2.2 V| |Yellow|585–595 nm|AlInGaP|2.0–2.2 V| |Green (InGaN)|515–530 nm|InGaN|2.8–3.4 V| |Blue|450–475 nm|InGaN|2.8–3.3 V| |White|Blue + phosphor|InGaN + YAG|2.8–3.3 V| |UV-A|365–405 nm|InGaN / GaN|3.0–3.9 V| Note: Typical forward voltage at 20 mA for standard indicator LEDs. High-power LEDs at 350 mA+ run 0.2–0.5 V higher. --- # LED strip power supply and voltage drop calculator URL: https://ledlights.org/tools/led-strip-power-calculator/ · Updated: 2026-11-15 **Definition (Voltage drop):** Voltage drop is the voltage lost in the copper of an LED strip and in the wires that feed it, because every conductor has some resistance. It grows with current and distance, so the far end of a long low-voltage strip receives less than the supply voltage and glows dimmer or changes color. ## LED strip calculator Enter the strip voltage, its power per metre and the run length. The calculator gives the total watts and amps, the smallest power supply to run at 80% load or less, the lowest voltage anywhere on the strip, how long a run each feed point can serve, and the wire size that keeps losses small. ## Sizing the power supply Multiply the strip's power per metre by its length, then divide by 0.8 so the supply runs at no more than 80% of its rating. Five metres of 14.4 W/m strip draws 72 W, so it needs a supply of at least 90 W, in practice 100 W, at the strip's own voltage. ## Why the far end of a strip is dimmer Current flows along two thin copper rails, and copper has resistance, so the voltage falls along the strip. Fed from one end, the drop at the far end is the total current × the rails' resistance per metre × the length ÷ 2. Because the current also grows with length, doubling a run quadruples the drop. Table: Longest LED strip run from one feed point (5% and 10% voltage drop) |Strip|Under 5% drop|Under 10% drop| |---|---|---| |5 V, 18 W/m (WS2812B, 60/m)|1.2 m (3.9 ft)|1.7 m (5.5 ft)| |12 V, 4.8 W/m|5.5 m (18 ft)|7.7 m (25 ft)| |12 V, 9.6 W/m|3.9 m (13 ft)|5.5 m (18 ft)| |12 V, 14.4 W/m|3.2 m (10 ft)|4.5 m (15 ft)| |24 V, 9.6 W/m|7.7 m (25 ft)|11 m (36 ft)| |24 V, 14.4 W/m|6.3 m (21 ft)|8.9 m (29 ft)| |24 V, 19.2 W/m|5.5 m (18 ft)|7.7 m (25 ft)| |48 V, 14.4 W/m|12.6 m (41 ft)|17.9 m (59 ft)| Note: Strip copper only, about 0.10 Ω per metre for both rails, with no allowance for the feed wire. Feeding both ends doubles each figure; thin-copper budget strips manage about 30% less. If the maker states a shorter maximum run, use that. ## Power injection: feeding long runs Power injection means running extra wires from the supply to more points along the strip, so no stretch of copper carries current far. Feeding both ends cuts the drop to a quarter. For longer runs, add feed points every few metres, each with its own wire pair from the supply, and fuse each feed. ## Choosing the wire gauge The loss in the feed wire is the current × the resistance of both conductors, out and back. Keep it under about 2% of the strip voltage. At 12 V and 5 A, 18 AWG (about 0.75 mm²) manages 1.1 m from the supply; 14 AWG (2.5 mm²) reaches about 3 m, and twice as far at 24 V. ## 5 V, 12 V, 24 V or 48 V? Use 24 V for most white strips: at the same power it draws half the current of 12 V, so it loses half as many volts, a quarter as large a share of the supply. Choose 12 V for short runs and vehicles, 5 V only for addressable pixels, and 48 V for very long runs. --- # LED lighting-equivalent and energy-savings calculator URL: https://ledlights.org/tools/led-energy-savings-calculator/ · Updated: 2026-11-16 **Definition (Lumen equivalent):** A lumen equivalent is the LED that matches an older bulb or fixture by its light output in lumens. A 60 W incandescent bulb gives about 800 lumens, which an LED matches with roughly 8–9 W; LED watts equal the target lumens divided by LED efficacy. Commercial fixtures are matched by delivered lumens and system watts, not lamp watts. ## Energy savings calculator This calculator converts the incandescent, halogen or CFL bulbs you use into equivalent LED lumens and watts, then estimates the kilowatt-hours, money and CO₂ you save each year. For example, ten 60 W incandescent bulbs used five hours a day, replaced with 8 W LEDs, save about $160 a year at $0.17/kWh. ## Lumen equivalents Match brightness by lumens: a 40 W incandescent gives about 450 lumens, 60 W about 800, 75 W about 1,100, 100 W about 1,600 and 150 W about 2,600. At roughly 100 lumens per watt, LEDs match them with about 4–5, 8–9, 11–12, 14–16 and 22–26 watts. Table: Lumen equivalents: incandescent, halogen, CFL and LED watts |Incandescent|Halogen|CFL|Light output|LED (≈100 lm/W)| |---|---|---|---|---| |25 W|18 W|5 W|~210–250 lm|2–3 W| |40 W|29 W|9 W|~450 lm|4–5 W| |60 W|43 W|13 W|~800 lm|8–9 W| |75 W|53 W|18 W|~1,100 lm|11–12 W| |100 W|72 W|23 W|~1,600 lm|14–16 W| |150 W|—|42 W|~2,600 lm|22–26 W| Note: Approximate light output of common bulbs and the LED wattage that matches them. ## Method and assumptions Annual energy equals watts × bulbs × hours per day × 365 ÷ 1,000, and LED watts equal the target lumens divided by LED efficacy. Lifetime savings assume a 25,000-hour LED versus about 1,000 hours for incandescent, 2,000 for halogen and 8,000 for CFL, and CO₂ uses a U.S. grid average of 0.37 kg/kWh. ## Commercial fixture equivalents: metal halide, HPS and fluorescent Match commercial fixtures by delivered lumens and system watts, not lamp watts. A 400 W metal-halide high-bay draws about 458 W with its ballast and delivers roughly 19,000 lumens, which a 135–150 W LED high-bay matches. A three-lamp T8 troffer drawing 85 W is matched by a 35–40 W LED panel. Table: Commercial fixture equivalents: metal halide, HPS and fluorescent to LED |Existing fixture|System watts|Delivered lumens|LED at 140 lm/W|Energy saved| |---|---|---|---|---| |Metal halide, 175 W lamp|210 W|~7,350 lm|~53 W|75%| |Metal halide, 250 W lamp|295 W|~10,760 lm|~77 W|74%| |Metal halide, 400 W lamp (high-bay)|458 W|~18,900 lm|~135 W|71%| |Metal halide, 1000 W lamp (sports, flood)|1,080 W|~57,750 lm|~413 W|62%| |High-pressure sodium, 150 W lamp|188 W|~8,640 lm|~62 W|67%| |High-pressure sodium, 250 W lamp|295 W|~15,120 lm|~108 W|63%| |High-pressure sodium, 400 W lamp|465 W|~27,000 lm|~193 W|59%| |High-pressure sodium, 1000 W lamp|1,100 W|~75,600 lm|~540 W|51%| |T12, 2 × 40 W, magnetic ballast|86 W|~2,930 lm|~21 W|76%| |T8, 2 × 32 W|59 W|~3,410 lm|~24 W|59%| |T8, 3 × 32 W troffer|85 W|~5,120 lm|~37 W|57%| |T8, 4 × 32 W|112 W|~6,820 lm|~49 W|57%| |T5HO, 4 × 54 W high-bay|234 W|~15,810 lm|~113 W|52%| |T5HO, 6 × 54 W high-bay|351 W|~23,700 lm|~169 W|52%| Note: System watts include the ballast. Delivered lumens are mean lamp lumens after fixture losses. LED watts assume 140 lm/W, typical of current DLC-listed high-bays, area lights and troffers. ## Payback, ROI and utility rebates Simple payback is the net project cost after utility rebates divided by the annual energy savings. Retrofits that replace metal halide or high-pressure sodium fixtures running 12 hours a day often pay back within one to three years, and avoided relamping, lift rental and occupancy sensors shorten that further. --- # Compare LED types and legacy light sources URL: https://ledlights.org/compare/ · Updated: 2026-11-16 ## Comparison table This table compares 25 light sources: 19 LED and OLED types and six legacy lamps. Mid-power SMD 2835 and 3030 LEDs reach 220 lumens per watt against 10–17 for incandescent bulbs, an SMD 3030 lasts 50,000–100,000 hours against 750–2,000, and every LED type is mercury-free, unlike fluorescent, metal halide and sodium lamps. Table: Comparison of 25 light sources: LED types and legacy lamps |Type|Efficacy (lm/W)|Lifespan (h)|CRI|Heat handling|Cost|Mercury-free|Dimmable|Typical applications| |---|---|---|---|---|---|---|---|---| |DIP 3 / 5 mm|20–90|20,000–50,000|65–80|Poor (leads only)|$|Yes|Yes (PWM or current)|Indicators, hobby electronics, large-pitch signs| |Piranha / superflux|40–80|30,000–50,000|65–80|Fair (4 leads)|$|Yes|Yes (PWM or current)|Older tail lights, signage, accent| |SMD 3528|60–100|25,000–50,000|70–90|Fair|$|Yes|Yes (PWM or current)|Low-output strips, backlights| |SMD 2835|120–220|35,000–60,000|80–97|Good (thermal pad)|$|Yes|Yes (PWM or current)|Bulbs, tubes, panels, efficient white strips| |SMD 3030 (EMC)|150–220|50,000–100,000|70–90|Very good|$$|Yes|Yes (PWM or current)|High-bays, streetlights, horticulture| |SMD 5050 (white)|70–110|30,000–50,000|70–90|Fair|$|Yes|Yes (PWM or current)|Signage, legacy strips, tunable/RGBW strips| |SMD 5630 / 5730|100–150|30,000–50,000|70–90|Good|$|Yes|Yes (PWM or current)|Panels, troffers, T8 tubes, corn bulbs| |High-power emitter (1–10 W)|100–200|50,000–100,000|70–95|Excellent with heat sink|$$|Yes|Yes (PWM or current)|Flashlights, headlamps, floodlights, bike lights| |COB (10–200 W)|100–180|30,000–60,000|80–98|Needs a large heat sink|$$|Yes|Yes (PWM or current)|Downlights, spotlights, retail, high-bay, stage| |CSP (flip-chip)|130–200|50,000+|70–90|Excellent (direct to PCB)|$$|Yes|Yes (PWM or current)|Backlights, automotive headlamps, flash, dense arrays| |Filament (COG)|100–160|15,000–25,000|80–90|Fair (gas-cooled bulb)|$|Yes|Varies (bulbs marked dimmable)|Decorative clear bulbs, pendants, chandeliers| |OLED|40–90 (panels)|20,000–100,000|85–95 (lighting)|Low heat, area source|$$$|Yes|Yes (PWM or current)|Phones, watches, TVs, design luminaires| |QLED (QD-enhanced LCD)|—|50,000–100,000|—|Good|$$|Yes|Yes (backlight)|TVs, monitors| |Mini-LED backlight|—|50,000–100,000|—|Good|$$$|Yes|Yes (backlight)|HDR TVs, tablets, laptops, monitors| |MicroLED|—|100,000 (projected)|—|Good|$$$$|Yes|Yes (per pixel)|Premium modular walls, AR microdisplays, watches| |IR 850 / 940 nm|— (WPE 30–50%)|50,000+|n/a|Good|$|Yes|Yes (PWM or current)|CCTV, remotes, sensors, optocouplers, PBM| |UV-A 365–405 nm|— (WPE 20–60%)|10,000–30,000|n/a|Fair|$$|Yes|Yes (PWM or current)|Curing, 3D printing, inspection, forensics| |UV-C 255–280 nm|— (WPE 2–10%)|5,000–20,000|n/a|Poor (high heat per mW)|$$$|Yes|Yes (PWM or current)|Water, air and surface disinfection| |Addressable 5050 (WS2812B)|40–80 (white)|25,000–50,000|50–70 (RGB white)|Fair|$$|Yes|Yes (built-in PWM)|Pixel strips, DJ and stage, gaming, art| |Incandescent|10–17|750–2,000|100|Very hot (~90% IR)|$|Yes|Yes (phase-cut dimmer)|Phased out for general lighting| |Halogen|15–24|2,000–4,000|100|Very hot|$|Yes|Yes (phase-cut dimmer)|Old spotlights and headlamps| |CFL|50–70|8,000–10,000|80–85|Warm; contains mercury|$|No (contains mercury)|Varies (models marked dimmable)|Phased out in the EU (2023)| |Linear fluorescent T8|80–100|20,000–36,000|80–86|Ballast losses; mercury|$|No (contains mercury)|Varies (needs a dimming ballast)|Offices and schools, being retrofitted| |Metal halide|65–115|10,000–20,000|65–95|Very hot; slow restrike|$$|No (contains mercury)|Varies (needs a dimming ballast)|Old high-bays and stadiums| |High-pressure sodium|80–140|~24,000|20–25|Hot; slow warm-up|$|No (contains mercury)|Varies (needs a dimming ballast)|Old streetlights, greenhouses| Note: Values are typical ranges for current-generation products. "—" marks display and specialty emitters for which lumens per watt or CRI is not a meaningful metric; their wall-plug efficiency (WPE) is shown instead where it applies. ## How to read the columns Efficacy is light output per watt of electrical input, in lumens per watt. Lifespan is the rated hours of use, for LEDs usually the L70 point where output has fallen to 70% of its initial value. CRI scores color rendering up to 100. Values are typical ranges for current-generation products, not guarantees for any one model. ## Head-to-head comparison guides Each comparison guide takes one buying decision and settles it with the numbers: SMD 2835 against 5050 and 3030 packages, COB against SMD and CSP, OLED against QLED, Mini-LED and MicroLED screens, and look-alike bulb bases such as E26 and E27 or GU10 and MR16.